200G QSFP56 DAC Cables – www.philisun.com https://www.philisun.com Optical transceivers support <strong>10G to 800G</strong> high-speed transmission Thu, 12 Mar 2026 08:51:10 +0000 en-US hourly 1 https://www.philisun.com/wp-content/uploads/2025/10/philisun斐立飒-logo彩色方形-1-100x100.png 200G QSFP56 DAC Cables – www.philisun.com https://www.philisun.com 32 32 200G QSFP56 to 4×50G SFP56 Passive Direct Attach Copper Twinax Cable (DAC) https://www.philisun.com/products/200g-qsfp56-4-50g-sfp56-dac/ Thu, 12 Mar 2026 08:39:40 +0000 https://www.philisun.com/?post_type=product&p=7578 Compliant with SFF-8661、SFF-8432、IEEE 802.3bs-200GAUI-4、IEEE802.3cd-50GAUI-1、SFP-8636、SFF-8472 standard
Switch to Switch
Switch to GPU

200G QSFP56 to 4×50G SFP56 Passive Direct Attach Copper Twinax Cable (DAC)最先出现在www.philisun.com。

]]>
SPECIFICATIONS
Cable End Connector AQSFP56Cable End Connector B4×SFP56
Jumper TypeActive Optical Breakout CableData Rate200G
Aggregate Bit Rate200GbpsLane Bit Rate50Gbps
Number of Channels4Single Channel Rate50G
Minimum Bend Radius5X Cable OD -Single, 10X Cable OD - RepeatedFactory BrandPHILISUN
Attenuation26AWG:10dB/8.5m maximum
28AWG:10dB/7m maximum
30AWG:8.4dB/5.5m maximum		Bit Error Rate≤10-12
ShieldBraid/FoilWire AWG26AWG/28AWG/30AWG
Cable TypePassive TwinaxCable OD30AWG: 7.8mm
28AWG: 7.0mm
26AWG: 7.0mm
Cable Colour/MaterialBlack PVC(OFNR)Cable Length Selection0.5-3.5 meter
ProtocolsSFF-8661/SFF-8432/IEEE 802.3bs-200GAUI-4/ IEEE802.3cd-50GAUI-1/SFP-8636/SFF-8472/SFF-8679Application Scenarios200Gigabit Ethernet (200GbE)
Supply Voltage3.3VPower Dissipation<0.1W
Operating Temperature0 to 70℃ (32 to 158℉)Storage Temperature-40 to 85℃ (-40 to 185℉)

 

PRODUCT PRESENTATION
The PHILISUN 200G QSFP56 to 4x50G SFP56 Passive Direct Attach Copper Twinax Cable (DAC) is an essential Breakout Cable solution, converting a single 200G QSFP56 port into four independent 50G SFP56 channels. It is fully compliant with SFF-8661, SFF-8432, IEEE 802.3bs and IEEE 802.3cd standards, ensuring reliable performance in Data Center environments. This Passive Copper solution delivers Ultra-Low Latency and is highly Cost-Effective for maximizing port density, supporting scalable links from Switch to Switch and high-throughput connections from Switch to GPU servers.

 

DAC SERIES PRODUCTS

 

PRODUCTION & TESTING EQUIPMENT

 

QSFP56 Pin Define

 

QSFP56 to 4×SFP56 Pin Function Definition
PIN Logic Symbol Description Notes
1 – GND Ground 1
2 CML-I Tx2n Transmitter Inverted Data Input –
3 CML-I Tx2p Transmitter Non-Inverted Data Input –
4 – GND Ground 1
5 CML-I Tx4n Transmitter Inverted Data Input –
6 CML-I Tx4p Transmitter Non-Inverted Data Input –
7 – GND Ground 1
8 LVTTL-I ModSelL Module Select –
9 LVTTL-I ResetL Module Reset –
10 – VccRx +3.3 V Power Supply Receiver 2
11 LVCMOS-I/O SCL 2-wire serial interface clock –
12 LVCMOS-I/O SDA 2-wire serial interface data –
13 – GND Ground 1
14 CML-O Rx3p Receiver Non-Inverted Data Output –
15 CML-O Rx3n Receiver Inverted Data Output –
16 – GND Ground 1
17 CML-O Rx1p Receiver Non-Inverted Data Output –
18 CML-O Rx1n Receiver Inverted Data Output –
19 – GND Ground 1
20 – GND Ground 1
21 CML-O Rx2n Receiver Inverted Data Output –
22 CML-O Rx2p Receiver Non-Inverted Data Output –
23 – GND Ground 1
24 CML-O Rx4n Receiver Inverted Data Output –
25 CML-O Rx4p Receiver Non-Inverted Data Output –
26 – GND Ground 1
27 LVTTL-O ModPrsL Module Present –
28 LVTTL-O IntL Interrupt –
29 – VccTx +3.3V Power supply transmitter 2
30 – Vcc1 +3.3V Power supply 2
31 LVTTL-I InitMode Initialization mode; In legacy QSFP applications, the
InitMode pad is called LPMODE		 –
32 – GND Ground 1
33 CML-I Tx3p Transmitter Non-Inverted Data Input –
34 CML-I Tx3n Transmitter Inverted Data Input –
35 – GND Ground 1
36 CML-I Tx1p Transmitter Non-Inverted Data Input –
37 CML-I Tx1n Transmitter Inverted Data Input –
38 – GND Ground 1
39 – GND Ground 1
40 CML-I Tx6n Transmitter Inverted Data Input –
41 CML-I Tx6p Transmitter Non-Inverted Data Input –
42 – GND Ground 1
43 CML-I Tx8n Transmitter Inverted Data Input –
44 CML-I Tx8p Transmitter Non-Inverted Data Input –
45 – GND Ground 1
46 – Reserved For future use 3
47 – VS1 Module Vendor Specific 1 3
48 – VccRx1 3.3V Power Supply 2
49 – VS2 Module Vendor Specific 2 3
50 – VS3 Module Vendor Specific 3 3
51 – GND Ground 1
52 CML-O Rx7p Receiver Non-Inverted Data Output –
53 CML-O Rx7n Receiver Inverted Data Output –
54 – GND Ground 1
55 CML-O Rx5p Receiver Non-Inverted Data Output –
56 CML-O Rx5n Receiver Inverted Data Output –
57 – GND Ground 1
58 – GND Ground 1
59 CML-O Rx6n Receiver Inverted Data Output –
60 CML-O Rx6p Receiver Non-Inverted Data Output –
61 – GND Ground 1
62 CML-O Rx8n Receiver Inverted Data Output –
63 CML-O Rx8p Receiver Non-Inverted Data Output –
64 – GND Ground 1
65 – NC No Connect 3
66 – Reseved For future use 3
67 – VccTx1 3.3V Power Supply 2
68 – Vcc2 3.3V Power Supply 2
69 – Reseved For future use 3
70 – GND Ground 1
71 CML-I Tx7p Transmitter Non-Inverted Data Input –
72 CML-I Tx7n Transmitter Inverted Data Input –
73 – GND Ground 1
74 CML-I Tx5p Transmitter Non-Inverted Data Input –
75 CML-I Tx5n Transmitter Inverted Data Input –
76 – GND Ground 1
Notes:
1. QSFP56 TO 2 QSFP uses common ground (GND) for all signals and supply (power). All are common within the QSFP56 TO 2 QSFP module and all module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board  signal-common ground plane.
2.VccRx, VccRx1, Vcc1, Vcc2, VccTx and VccTx1 shall be applied concurrently. Requirements defined for the host side of the Host Card Edge Connector are listed in Table 6. VccRx, VccRx1, Vcc1, Vcc2, VccTx and VccTx1 may be internally connected within the module in any combination. The connector Vcc pins are each rated for a maximum current of 1000 mA
3. All Vendor Specific, Reserved and No Connect pins may be terminated with 50 ohms to ground on the host. Pad 65 (No Connect) shall be left unconnected within the module. Vendor specific and Reserved pads shall have an impedance to GND that is greater than 10 kOhms and less than 100 pF.
4. Plug Sequence specifies the mating sequence of the host connector and module. The sequence is 1A, 2A, 3A, 1B, 2B, 3B. (see Figure 2 for pad locations) Contact sequence A will make, then break contact with additional QSFP56 TO 2 QSFP pads. Sequence 1A, 1B will then occur simultaneously, followed by 2A, 2B, followed by 3A,3B.

 

Host PCB SFP56 pad contact assignment

 

SFP56 Pin Descriptions
Pin Logic Symbol Description Notes
1 – VeeT Transmitter Ground –
2 – TX_Fault N/A 1
3 LV-TTL-I TX_DIS Transmitter Disable 2
4 LV-TTL-I/O SDA Tow Wire Serial Data –
5 LV-TTL-I SCL Tow Wire Serial –
6 MOD_DEF0 Module present, –
7 LV-TTL-I RS0 N/A 1
8 LV-TTL-O LOS LOS of Signal 2
9 LV-TTL-I RS1 N/A 1
10 – VeeR Reciever Ground –
11 – VeeR Reciever Ground –
12 CML-O RD- Reciever Data Inverted –
13 CML-O RD+ Reciever Data –
14 – VeeR Reciever Ground –
15 – VccR Reciever Supply 3.3V –
16 – VccT Transmitter Supply –
17 – VeeT Transmitter Ground –
18 CML-I TD+ Transmitter Data –
19 CML_I TD- Transmitter Data –
20 – VeeT Transmitter Ground –
Notes:
1. Signals not supported in SFP56 Copper pulled-downto VeeT with 30K ohms resistor
2. Passive cable assemblies do not support  LOS and TX_DIS

 

PRODUCT CERTIFICATION

 

COMPATIBLE BRANDS
CONFIGURATION INFORMATION
The form can be filled in the actual website url.

 

200G QSFP56 to 4×50G SFP56 Passive Direct Attach Copper Twinax Cable (DAC)最先出现在www.philisun.com。

]]> 200G QSFP56 to QSFP56 Passive Direct Attach Copper Twinax Cable (DAC) https://www.philisun.com/products/200g-qsfp56-to-qsfp56-passive-direct-attach-copper-twinax-cable-dac/ Thu, 12 Mar 2026 07:34:16 +0000 https://www.philisun.com/?post_type=product&p=7575 Compliant with IEEE802.3cd、SFF-8436 standard
Switch to Switch
Switch to GPU

200G QSFP56 to QSFP56 Passive Direct Attach Copper Twinax Cable (DAC)最先出现在www.philisun.com。

]]>
SPECIFICATIONS
Cable End Connector AQSFP56Cable End Connector BQSFP56
Jumper TypeDirect-AttachData Rate200G
Aggregate Bit Rate200GbpsLane Bit Rate50Gbps
Number of Channels4Single Channel Rate50G
Minimum Bend Radius5X Cable OD -Single, 10X Cable OD - RepeatedFactory BrandPHILISUN
Attenuation26AWG:10dB/8.5m maximum
30AWG:8.4dB/5.5m maximum		Bit Error Rate≤10-12
ShieldBraid/FoilWire AWG26AWG/30AWG
Cable TypePassive TwinaxCable OD30AWG: 7.8mm
26AWG: 6.0mm
Cable Colour/MaterialBlack PVC(OFNR)Cable Length Selection0.5-3.5 meter
ProtocolsIEEE 802.3cd/ QSFP56 MSA/SFF-8661/SFF-8636/SFF-8417/SFF-8679/Application Scenarios200Gigabit Ethernet (200GbE)
Supply Voltage3.3VPower Dissipation<0.03W
Operating Temperature0 to 70℃ (32 to 158℉)Storage Temperature-40 to 85℃ (-40 to 185℉)

 

PRODUCT PRESENTATION
The PHILISUN 200G QSFP56 to QSFP56 Passive Direct Attach Copper Twinax Cable (DAC) delivers a robust, point-to-point solution for 200 Gigabit Ethernet using PAM4 signaling. It is compliant with the IEEE 802.3cd and SFF-8436 Standard, providing highly reliable connectivity. This Passive Copper solution is Cost-Effective and offers Ultra-Low Latency over short runs, making it an ideal choice for direct Switch to Switch communication and essential Server Interconnect paths from Switch to GPU within the rack.

 

DAC SERIES PRODUCTS

 

PRODUCTION & TESTING EQUIPMENT

 

PERFORMANCE PARAMETER
Recommended Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Ref.
Storage Temperature – -40 – +85 ℃ –
Operating Case Temperature Tc 0 – +70 ℃ –
Power Supply Voltage VCC3 3.14 3.3 3.47 V –
Data Rate Per Lane – 1 – 50 Gb/s –

 

Electrical Characteristics
Item Specification Notes
SDD21 & SDD12 -17.16 dB Min. @13.28 GHz From 0.01 GHz-19GHz
SDD11 & SDD22 -16.5+2*sqrt(f)dB Max. @0.05GHz~4.1GHz
-10.66+14*log(f/5.5)dB Max.@4.1GHz~10GHz		 From 0.01 GHz- 19GHz
SCD21-SDD21 -10 dB Max. @0.01 GHz~12.89 GHz
-27+(29/22)*fdB Max. @12.89 GHz~15.7 GHz
-6.3 dB Max. @15.7 GHz~19 GHz		 From 0.01 GHz- 19GHz

 

Pin Definition

 

PIN Logic Symbol Description Notes
1 – GND Ground 1
2 CML-I Tx2n Transmitter Inverted Data –
3 CML-I Tx2p Transmitter Non-Inverted –
4 – GND Ground 1
5 CML-I Tx4n Transmitter Inverted Data –
6 CML-I Tx4p Transmitter Non-Inverted –
7 – GND Ground 1
8 LVTTL-I ModSelL Module Select –
9 LVTTL-I ResetL Module Reset –
10 – VccRx +3.3 V Power Supply 2
11 LVCMOS SCL 2-wire serial interface –
12 LVCMOS SDA 2-wire serial interface –
13 – GND Ground 1
14 CML-O Rx3p Receiver Non-Inverted –
15 CML-O Rx3n Receiver Inverted Data –
16 – GND Ground 1
17 CML-O Rx1p Receiver Non-Inverted –
18 CML-O Rx1n Receiver Inverted Data –
19 – GND Ground 1
20 – GND Ground 1
21 CML-O Rx2n Receiver Inverted Data –
22 CML-O Rx2p Receiver Non-Inverted –
23 – GND Ground 1
24 CML-O Rx4n Receiver Inverted Data –
25 CML-O Rx4p Receiver Non-Inverted –
26 – GND Ground 1
27 LVTTL-O ModPrsL Module Present –
28 LVTTL-O IntL Interrupt –
29 – Vcc Tx +3.3V Power supply 2
30 – Vcc1 +3.3V Power supply 2
31 LVTTL-I LPMode Low Power Mode –
32 – GND Ground 1
33 CML-I Tx3p Transmitter Non-Inverted –
34 CML-I Tx3n Transmitter Inverted Data –
35 – GND Ground 1
36 CML-I Tx1p Transmitter Non-Inverted –
37 CML-I Tx1n Transmitter Inverted Data –
38 – GND Ground 1
Notes:
1. GND is the symbol for signal and supply (power) common for the QSFP+ module. All are common within the QSFP+ module and all module voltages are referenced to this potential unless otherwise noted. Connect these  directly to the hostboard signal-common ground plane.
2.Vcc Rx, Vcc1 and Vcc Tx are the receiver and transmitter power supplies and shall be applied concurrently. Requirements defined for the host side of the Host Edge Card Connector are listed in Table 6. Recommended host board power supply filtering is shown in Figure 4. Vcc Rx Vcc1 and Vcc Tx may be internally connected within the QSFP+ Module module in any combination. The connector pins are each rated for a maximum current of 500 mA.

 

PRODUCT CERTIFICATION

 

COMPATIBLE BRANDS
CONFIGURATION INFORMATION
The form can be filled in the actual website url.

 

200G QSFP56 to QSFP56 Passive Direct Attach Copper Twinax Cable (DAC)最先出现在www.philisun.com。

]]>