100G SFP-DD AOC Cables – www.philisun.com https://www.philisun.com Optical transceivers support <strong>10G to 800G</strong> high-speed transmission Fri, 27 Feb 2026 06:11:17 +0000 en-US hourly 1 https://www.philisun.com/wp-content/uploads/2025/10/philisun斐立飒-logo彩色方形-1-100x100.png 100G SFP-DD AOC Cables – www.philisun.com https://www.philisun.com 32 32 100G SFP-DD to SFP-DD Active Optical Cable (AOC) https://www.philisun.com/products/sfp-dd-100g-aoc/ Fri, 21 Nov 2025 01:59:58 +0000 https://www.philisun.com/?post_type=product&p=3451 Compliant with the SFF-8432 SFP-DD MSA standard
Switch to Switch
Switch to GPU
Switch to Network Card

100G SFP-DD to SFP-DD Active Optical Cable (AOC)最先出现在www.philisun.com。

]]>
SPECIFICATIONS
Cable End Connector ASFP-DDCable End Connector BSFP-DD
Jumper TypeDirect-AttachData Rate100G
Aggregate Bit Rate106.25GbpsLane Bit Rate53.125Gbps
Number of Channels2Single Channel Rate50G
Array TransmitterVSCELArray ReceiverPIN
Minimum Bend Radius60mmFactory BrandPHILISUN
Center(Operating) Wavelength850nmBit Error Rate2.4E-4
Fiber TypeOM3 MMF MAX 70m/OM4 MMF MAX 100mCable ColourAqua
Cable MaterialLSZH/OFNPCable Length Selection1-100meter
Safety CertificationTUV/UL/FDAApplication Scenarios100 Gigabit Ethernet (100GbE)
ProtocolsSFP-DD MSA/SFP-DD MISDDMI(Commercial)YES
Supply Voltage3.3VPower Dissipation<3.5W
Operating Temperature0 to 70℃ (32 to 158℉)Storage Temperature-20 to 85℃ (-4 to 185℉)

 

PRODUCT PRESENTATION
The PHILISUN SFP-DD(100G) Active Optical Cable is a direct-attach fiber assembly utilizing SFP-DD connectors and the Multi-Mode Fiber (MMF) scheme. The product complies with the SFF-8431 MSA standard and is suitable for 100Gbps connections within racks and across adjacent racks. It uses OM3/OM4 Multimode Fiber. Its compact structure and fully sealed integrated optics reduce costs compared to conventional optical modules and jumpers, while significantly improving reliability and reducing maintenance. This AOC guarantees broad compatibility with major vendor platforms including Cisco, H3C, Huawei, Juniper, and Arista, and more.

 

AOC SERIES PRODUCTS

 

PRODUCTION & TESTING EQUIPMENT

 

PERFORMANCE PARAMETER
Absolute Maximum Ratings
Parameters Symbol Min. Max. Unit
Power Supply Voltage VCC -0.5 +3.6 V
Storage Temperature Tc -40 +85 ℃
Relative Humidity RH 0 85 %

 

Recommended Operating Conditions
Parameter Symbol Min Typical Max Unit
Supply Voltage VCC 3.15 3.3 3.45 V
Supply current Icc – – 1060 mA
Operating Case Temperature(Standard) Tca 0 – 70 ºC
Data Rate per lane DR – 53.125 – Gbps
Fiber Bend Radius Rb 3 – – cm
Notes:
1. Supply current is shared between VccT ，VccR ，VccT1 and VccR1
2. In-rush is defined as current level above steady state current requirements.

 

Transmitter Specifications
Parameter Symbol Min Typical Max Unit
Input differential impedance Rin – 100 – Ω
Differential Data Input Swing Vin 300 – 1100 mV
Transmit Disable Voltage VD 2.0 – VCC+0.3 V
Transmit Enable Voltage Ven Vee – Vee+0.8 V

 

Receiver Specifications
Parameter Symbol Min Typical Max Unit
Differential Data Output Swing Vout 300 – 900 mV
Bit Error Rate BER – – 2.4E-4 –
Output Differential Impedance Rout – 100 – Ω
Loss of Signal -Asserted – 2.0 – VCC+0.3 V
Loss of Signal -Negated – Vee – Vee+0.8 V
Note：
1. BER=2.4E-4; PRBS31Q@26.5625GBd. Pre-FEC

 

TRANSCEIVER ELECTRICAL PAD LAYOUT

 

PIN DEFINITION
Pin Symbol Name/Description
1 GND Ground
2 TxFault Transmitter Fault
3 TxDisable Transmitter Disable for classic SFP channel
4 SDA 2-wire Serial Interface Data Line
5 SCL 2-wire Serial Interface Clock Line
6 Mod_ABS Module Absent. Grounded within the module
7 Speed1 Rx Rate Select for classic SFP channel
8 RxLOS SFP channel Loss of Signal indication. Logic 0 indicates normal operation
9 Speed2 Tx Rate Select for classic SFP channel
10 GND Ground
11 GND Ground
12 RD0- Receiver Inverted DATA out for classic SFP+ channel. AC Coupled
13 RD0+ Receiver DATA out for classic SFP+ channel. AC Coupled
14 GND Ground
15 VccR Receiver Power Supply
16 VccT Transmitter Power Supply
17 GND Ground
18 TD0+ Transmitter DATA in for classic SFP+ channel. AC Coupled
19 TD0- Transmitter Inverted DATA in for classic SFP+ channel. AC Coupled
20 GND Ground
21 GND Ground
22 IntL/ TxFaultDD Interrupt: optionally configured as TxFaultDD via TWI as described in the SFP-DD MIS
23 TxDisableDD Transmitter Disable for DD channel
24 ePPS/Clock Precision Time Protocol (PTP) reference clock input
25 LPMode Low Power Mode Control
26 ResetL Module Reset
27 Speed1DD Rx Rate Select for DD channel
28 RxLOSDD SFP DD channel Loss of Signal indication. Logic 0 indicates normal operation
29 Speed2DD Tx Rate Select for DD channel
30 GND Ground
31 GND Ground
32 RD1- Receiver Inverted DATA out for DD channel. AC Coupled
33 RD1+ Receiver DATA out for DD channel. AC Coupled
34 GND Ground
35 VccR1 Receiver Power for DD channel
36 VccT1 Transmitter Power for DD channel
37 GND Ground
38 TD1+ Transmitter DATA in for DD channel. AC Coupled
39 TD1- Transmitter Inverted DATA in for DD channel. AC Coupled
40 GND Ground

 

PRODUCT CERTIFICATION

 

COMPATIBLE BRANDS
CONFIGURATION INFORMATION
The form can be filled in the actual website url.

 

100G SFP-DD to SFP-DD Active Optical Cable (AOC)最先出现在www.philisun.com。

]]>