10G SFP+ Transceivers (8G–16G) – www.philisun.com

Generic Compatible 16G CWDM(1470-1610nm) SFP+ 10/40km DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Mon, 17 Nov 2025 09:53:03 +0000

SPECIFICATIONS
Product Model	SFP+16-CW1416-10/40-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate(OM3)	14.025Gbps	Channel Data Rate	14.025Gbps
Effective Transmission Distance	40km	Power Budget	14dB
Wavelength	1470nm to 1610nm	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	CWDM EML	Receiver Type	IDP
TX Power	0~4dBm	Receiver Sensitivity	-14dBm
Digital Optical Monitoring(DOM)	YES	Receiver Overload	0dBm
Power Consumption	<1.8W	Protocols	SFF-8431 SFF-8432 SFF-8472
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 16G CWDM (1470-1610nm) 10/40km LC DX series single-mode transceiver is a compact, pluggable module designed for serial optical data communications, such as 16x/8x/4x Fibre Channel applications. This module is optimized for single-mode fiber and operates at nominal CWDM wavelengths from 1470nm to 1610nm, with 20nm steps between each wavelength. It offers a guaranteed optical link budget of 14dB. Featuring an SFP+ 20-pin connector, the module supports hot-plug capability. The transmitter uses a CWDM EML laser, compliant with Class 1 laser safety standards under IEC-60825. The receiver employs a PIN detector and a limiting post-amplifier IC for reliable signal reception. The SFP+ 16G CWDM (1470-1610nm) 10/40km LC DX series is fully compliant with the SFP+ Multi-Source Agreement (MSA) Specification SFF-8431.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

CWDM Wavelength
Band	Nomenclature	Wavelength(nm)
		Min.	Typ.	Max.
S-band Short Wavelength	K	1464	1470	1477.5
	L	1484	1490	1497.5
	M	1504	1510	1517.5
	N	1524	1530	1537.5
C-band Conventional	O	1544	1550	1557.5
L-band Long Wavelength	P	1564	1570	1577.5
	Q	1584	1590	1597.5
	R	1604	1610	1617.5
*Note:8 Wavelengths from 1470nm to 1610nm, each step 20nm.

Absolute Maximum Ratings
Parameter	Symbol	Min.	Max.	Unit
Storage temperature	Ts	-45	+85	°C
Supply voltage	Vcc	-0.5	4	V
Input voltage	Vin	-0.5	Vcc	V
*Note:Exceeding any one of these values may destroy the device permanently

Recommended Operating Conditions
Parameter	Symbol	Min.	Typical	Max.	Units
Operating case temperature	TC	0	–	+70	°C
Power supply voltage	Vcc	3.15	3.3	3.45	V
Power supply current	Icc	–	430	545	mA
Surge current	ISurge	–	–	+30	mA
Baud rate	SFP+16-CW1416-10/40-LCD	4.25	14.025	–	Gbps

Performance Specifications–Electrical
Parameter	Symbol	Min.	Typ.	Max	Unit	Notes
Transmitter
CML inputs(Differential)	Vin	250	–	1000	mVpp	AC coupled inputs
Input impedance (Differential)	Zin	85	100	115	ohms	Rin > 100 kohms @ DC
Differential input S-parameter	SDD11	–	–	-10	dB	–
Differential to common mode conversion	SCD11	–	–	-10	dB	–
Tx_DISABLE input voltage – high	–	2	–	3.45	V	–
Tx_DISABLE input voltage – low	–	0	–	0.8	V	–
Tx_FAULT output voltage – high	–	2	–	Vcc+0.3	V	Io = 400µA; Host Vcc
Tx_FAULT output voltage – low	–	0	–	0.5	V	Io = -4.0mA
Receiver
CML outputs (Differential)	Vout	350	–	700	mVpp	AC coupled outputs
Output AC common mode voltage		0		15.0	mV	RMS
Output impedance (Differential)	Zout	85	100	115	ohm	–
Differential output S-parameter	SD22	–	–	-10	dB	–
Rx_LOS output voltage – high	–	2	–	Vcc+0.3	V	lo = 400µA; host Vcc
Rx_LOS output voltage – low	–	0	–	0.8	V	lo = -4.0mA
MOD_DEF ( 0:2 )	VoH	2.5	–	–	V	With serial ID
MOD_DEF ( 0:2 )	VoL	0	–	0.5	V	With serial ID

Performance Specifications–Optical
Parameter		Symbol	Min.	Typical	Max.	Unit
Power budget		–	–	14	–	dB
Data rate		–	4.25	14.025	–	Gbps
Transmitter
Optical wavelength		λ	λc–6	λc	λc+7.5	nm
-20dB spectrum width		Δλ	–	–	1	nm
Side mode suppression ratio		SMSR	30	–	–	dB
Average output power		Pout	0	–	+4	dBm
Extinction ratio		ER	8.2	–	–	dB
Average power of OFF transmitter		POFF	–	–	-30	dBm
Transmitter dispersion penalty		TDP	–	–	2.5	dB
TX disable assert time		t_off	–	–	10	us
TX_DISABLE negate time		t_on	–	–	1	ms
TX_BISABLE time to start reset		t_reset	10	–	–	us
Time to initialize, include reset of TX_FAULT		t_init	–	–	300	ms
TX_FAULT from fault to assertion		t_fault	–	–	100	us
Total jitter		TJ	–	–	0.28	UI(p-p)
Data dependant jitter		DDJ	–	–	0.1	UI(p-p)
Uncorrelated jitter		UJ	–	–	0.023	RMS
Receiver
Centre wavelength		λ	1260	–	1620	nm
Sensitivity		Pmin	–	–	-14	dBm
Receiver overload		Pmax	0	–	–	dBm
Optical return loss		ORL	–	–	-12	dB
LOS de-assert		LOSD	–	–	-16	dBm
LOS assert		LOSA	-26	–	–	dBm
LOS	High	–	2.0	–	VCC+0.3	V
	Low	–	0	–	0.8

SFP+ TRANSCEIVER ELECTRICAL PAD LAYOUT

PIN FUNCTION DEFINITIONS

Pin	Name	Function	Plug Seq.	Notes
1	VeeT	Transmitter ground	1	Note 5
2	TX Fault	Transmitter fault indication	3	Note 1
3	TX Disable	Transmitter disable	3	Note 2, module disables on high or open
4	SDA	Module definition 2	3	2-Wire serial interface data line.
5	SCL	Module definition 1	3	2-Wire serial Interface clock.
6	MOD-ABS	Module definition 0	3	Note 3
7	RS0	RX rate select(LVTTL).	3	Rate select 0, optionally controls SFP+ module receiver. This pin is pulled low to VeeT with a>30K resistor..
8	LOS	Loss of signal	3	Note 4
9	RS1	TX rate select(LVTTL).	1	Rate select 1, optionally controls SFP+ module transmitter. This pin is pulled low to VeeT with a >30K resistor.
10	VeeR	Receiver ground	1	Note 5
11	VeeR	Receiver ground	1	Note 5
12	RD-	Inv. received data out	3	Note 6
13	RD+	Received data out	3	Note 7
14	VeeR	Receiver ground	1	Note 5
15	VccR	Receiver power	2	3.3V ± 5%, Note 7
16	VccT	Transmitter power	2	3.3V ± 5%, Note 7
17	VeeT	Transmitter ground	1	Note 5
18	TD+	Transmit data in	3	Note 8
19	TD-	Inv. transmit data in	3	Note 8
20	VeeT	Transmitter ground	1	Note 5
Notes: 1) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT/R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.2) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7K – 10 KΩ resistor. Its states are: Low (0 – 0.8V): Transmitter on (>0.8, < 2.0V): Undefined High (2.0 – 3.465V): Transmitter Disabled Open: Transmitter Disabled3) Module Absent, connected to VeeT or VeeR in the module. 4) RX LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor. Pull up voltage between 2.0V and VccT/R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. 5) The module signal ground contacts, VeeR and VeeT, should be isolated from the module case. 6) RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. 7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP+ connector pin. Maximum supply current is 360mA. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP+ input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP+ transceiver module will result in an inrush current of no more than 30mA greater than the steady state value. VccR and VccT may be internally connected within the SFP+ transceiver module. 8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board.

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 16G CWDM(1470-1610nm) SFP+ 10/40km DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 16G LR SFP+ 1310nm 10km DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Mon, 17 Nov 2025 09:22:00 +0000

SPECIFICATIONS
Product Model	SFP+16-13-10(LR)-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate(OM3)	14.025Gbps	Channel Data Rate	14.025Gbps
Effective Transmission distance	10km
Wavelength	1310nm	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	DFB	Receiver Type	IDP
TX Power	-5~2dBm	Receiver Sensitivity	-12dBm
Digital Optical Monitoring(DOM)	YES	Receiver Overload	2dBm
Power Consumption	<1.2W	Protocols	MSA SFP+ SFF-8431
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Industrial)	-40℃~+85℃	Storage Temperature(Industrial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 16G 1310nm 10km LR LC DX series single-mode transceiver is a compact, pluggable module designed for serial optical data communications, including 16x/8x/4x Fiber Channel applications. It features an SFP+ 20-pin connector, enabling hot-plug capability. Optimized for single-mode fiber, this module operates at a nominal wavelength of 1310nm. The transmitter uses a 1310nm multiple quantum well DFB laser, compliant with Class 1 laser safety standards under IEC-60825. The receiver integrates an InGaAs detector preamplifier (IDP) within an optical header, paired with a limiting post-amplifier IC for reliable signal processing.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

Absolute Maximum Ratings
Parameter	Symbol	Min.	Max.	Unit
Storage temperature	Ts	-45	+100	°C
Supply voltage	Vcc	-0.5	4	V
Operating relative humidity	RH	5	95	%
*Note:Exceeding any one of these values may destroy the device permanently.

Recommended Operating Conditions
Parameter	Symbol		Min.	Typical	Max.	Units
Case operating temperature	TC	Standard	0	–	+70	°C
		Extended	-40	–	+85
Power supply voltage	Vcc		3.15	3.3	3.45	V
Power supply current	Icc		–	–	360	mA
Surge current	ISurge		–	–	+30	mA
Baud rate	–		4.25/8.5/14.025			Gbps

Performance Specifications–Electrical
Parameter	Symbol	Min.	Typ.	Max	Unit	Notes
Transmitter
CML inputs(Differential)	Vin	200	–	900	mVpp	AC coupled inputs
Input impedance (Differential)	Zin	85	100	115	ohms	Rin > 100 kohms @ DC
Tx_DISABLE input voltage – high	–	2	–	Vcc+0.3	V	–
Tx_DISABLE input voltage – low	–	-0.3	–	0.8	V	–
Tx_FAULT output voltage – high	–	2	–	Vcc+0.3	V	Io = 400µA; host Vcc
Tx_FAULT output voltage – low	–	0	–	0.5	V	Io = -4.0mA
Receiver
CML Outputs (Differential)	Vout	300	–	1000	mVpp	AC coupled outputs
Rx_LOS output voltage – high	–	2	–	Vcc+0.3	V	lo = 400µA; host Vcc
Rx_LOS output voltage – low	–	-0.3	–	0.8	V	lo = -4.0mA
MOD_DEF ( 0:2 )	VoH	2.5	–	–	V	With serial ID
MOD_DEF ( 0:2 )	VoL	0	–	0.5	V	With serial ID

Optical and Electrical Characteristics
Parameter	Symbol	Min.	Typical	Max.	Unit
9µm core diameter SMF	–	–	–	10	Km
Data rate	–	4.25/8.5/14.025			Gbps
Transmitter
Centre wavelength	λC	1295	1310	1325	nm
Spectral width (-20dB)	Δλ	–	–	1	nm
Average output power@14.025Gb/s	Pout	-5	–	+2	dBm
Extinction ratio@14.025Gb/s	ER	3.5	–	–	dB
Average power of OFF transmitter	POFF	–	–	-30	dBm
Side mode suppression ratio	SMSR	30	–	–	dB
Transmitter dispersion penalty	TDP	–	–	4.4	dB
Input differential impedance	ZIN	90	100	110	Ω
TX disable assert time	t_off	–	–	10	us
TX_DISABLE negate time	t_on	–	–	1	ms
TX_BISABLE time to start reset	t_reset	10	–	–	us
Time to initialize, include reset of TX_FAULT	t_init	–	–	300	ms
TX_FAULT from fault to assertion	t_fault	–	–	100	us
Receiver
Centre wavelength	λ	1260	–	1370	nm
Sensitivity(OMA)@14.025Gb/s	Pmin	–	–	-12	dBm
Receiver overload	Pmax	2	–	–	dBm
Optical return loss	ORL	–	–	-12	dB
LOS de-assert@14.025Gb/s	LOSD	–	–	-19	dBm
LOS assert@14.025Gb/s LOSA -30 dBm	LOSA	-30	–	–	dBm

SFP+ TRANSCEIVER ELECTRICAL PAD LAYOUT

PIN FUNCTION DEFINITIONS

Pin	Name	Function	Plug Seq.	Notes
1	VeeT	Transmitter ground	1	Note 5
2	TX Fault	Transmitter fault indication	3	Note 1
3	TX Disable	Transmitter disable	3	Note 2, module disables on high or open
4	SDA	Module definition 2	3	2-Wire serial interface data line.
5	SCL	Module definition 1	3	2-Wire serial Interface clock.
6	MOD-ABS	Module definition 0	3	Note 3
7	RS0	RX rate select(LVTTL).	3	Rate select 0, optionally controls SFP+ module receiver. This pin is pulled low to VeeT with a>30K resistor..
8	LOS	Loss of signal	3	Note 4
9	RS1	TX rate select(LVTTL).	1	Rate select 1, optionally controls SFP+ module transmitter. This pin is pulled low to VeeT with a >30K resistor.
10	VeeR	Receiver ground	1	Note 5
11	VeeR	Receiver ground	1	Note 5
12	RD-	Inv. received data out	3	Note 6
13	RD+	Received data out	3	Note 7
14	VeeR	Receiver ground	1	Note 5
15	VccR	Receiver power	2	3.3V ± 5%, Note 7
16	VccT	Transmitter power	2	3.3V ± 5%, Note 7
17	VeeT	Transmitter ground	1	Note 5
18	TD+	Transmit data in	3	Note 8
19	TD-	Inv. transmit data in	3	Note 8
20	VeeT	Transmitter ground	1	Note 5
Notes: 1) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT/R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.2) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7K – 10 KΩ resistor. Its states are: Low (0 – 0.8V): Transmitter on (>0.8, < 2.0V): Undefined High (2.0 – 3.465V): Transmitter Disabled Open: Transmitter Disabled3) Module Absent, connected to VeeT or VeeR in the module. 4) RX LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor. Pull up voltage between 2.0V and VccT/R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. 5) The module signal ground contacts, VeeR and VeeT, should be isolated from the module case. 6) RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. 7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP+ connector pin. Maximum supply current is 360mA. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP+ input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP+ transceiver module will result in an inrush current of no more than 30mA greater than the steady state value. VccR and VccT may be internally connected within the SFP+ transceiver module. 8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board.

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 16G LR SFP+ 1310nm 10km DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 16G SR SFP+ 850nm 100m DOM Duplex LC MMF Optical Transceiver Module

philisun001 — Mon, 17 Nov 2025 07:57:31 +0000

SPECIFICATIONS
Product Model	SFP+16-85-01(SR)-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate(OM3)	14.025Gbps	Channel Data Rate	14.025Gbps
Effective Transmission distance(OM3)	100m
Wavelength	850nm	Operating Voltage	3.3V
Fiber Type	MMF	Core Size	50/125µm
Transmitter Type	VCSEL	Receiver Type	IDP
TX Power	-7.8dBm	Receiver Sensitivity	-10.5dBm
Digital Optical Monitoring(DOM)	YES	Receiver Overload	-0dBm
Power Consumption	<1.0W	Protocols	MSA SFP+ SFF-8431
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Industrial)	-40℃~+85℃	Storage Temperature(Industrial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 16G 850nm 100m SR LC DX series multi-mode transceiver is an SFP+ module designed for duplex optical data communications at speeds up to 14.025G. Equipped with a 20-pin SFP+ connector, it supports hot-plug capability, and offers digital diagnostic functions via an I2C interface. This module is optimized for multi-mode fiber and operates at a nominal wavelength of 850nm. The transmitter uses a Vertical Cavity Surface Emitting Laser (VCSEL), compliant with Class 1 laser safety standards under IEC 60825. The receiver section features an integrated GaAs detector preamplifier (IDP) within an optical header, along with a limiting post-amplifier IC for efficient signal processing.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

Absolute Maximum Ratings
Parameter	Symbol	Min.	Max.	Unit
Storage temperature	TS	-40	+85	°C
Supply voltage	VCC	-0.5	3.6	V
Input voltage	Vin	-0.5	Vcc	V
Output current	Io	–	50	mA

Recommended Operating Conditions
Parameter	Symbol		Min.	Typical	Max.	Units
Case operating temperature	TC	SFP+16-85-01(SR)-LCD	0	–	70	°C
			0	–	75
Power supply voltage	Vcc		3.15	3.3	3.45	V
Power supply current	Icc		–	–	300	mA
Surge current	ISurge		–	–	+30	mA
Data rate	–		–	14.025	–	Gbps

Performance Specifications–Electrical
Parameter	Symbol	Min.	Typ.	Max	Unit	Notes
Transmitter
CML inputs(Differential)	Vin	150	–	1200	mVpp	AC coupled inputs
Input impedance (Differential)	Zin	90	100	115	ohms	Rin > 100 kohms @ DC
Tx_DISABLE input voltage – high	–	2	–	Vcc+0.3	V	–
Tx_DISABLE input voltage – low	–	0	–	0.8	V	–
Tx_FAULT output voltage – high	–	2	–	Vcc+0.3	V	Io = 400µA; Host Vcc
Tx_FAULT output voltage – low	–	0	–	0.8	V	Io = -4.0Ma
Receiver
CML outputs (Differential)	Vout	350	–	700	mVpp	AC coupled outputs
Output impedance (Differential)	Zout	90	100	115	ohms	–
Rx_LOS output voltage – high	–	2.4	–	Vcc+0.3	V	lo = 400µA; host Vcc
Rx_LOS output voltage – low	–	0	–	0.4	V	lo = -4.0Ma
MOD_DEF ( 0:2 )	VoH	2.5	–	–	V	With serial ID
MOD_DEF ( 0:2 )	VoL	0	–	0.5	V	With serial ID

Optical and Electrical Characteristics
Parameter		Symbol	Min.	Typical	Max.	Unit
OM3 MMF		–	–	100	–	m
Data rate		–	–	14.025	–	Gbps
Transmitter
Centre wavelength		λC	840	850	860	nm
Spectral width (RMS)		Δλ	–	–	0.59	nm
Average output power		Pout	-7.8	–	–	dBm
Extinction ratio		ER	3.0	5.0	–	dB
Transmitter dispersion penalty		TDP	–	–	4.3	dB
Input differential impedance		ZIN	90	100	110	Ω
TX disable	Disable	–	2.0	–	Vcc+0.3	V
	Enable		0	–	0.8
TX_fault	Fault	–	2.4	–	VCC+0.3	V
	Normal		0	–	0.4
TX_disable assert time		t_off	–	–	10	us
TX_DISABLE negate time		t_on	–	–	1	ms
TX_BISABLE time to start reset		t_reset	10	–	–	us
Time to initialize, include reset of TX_FAULT		t_init	–	–	300	ms
TX_FAULT from fault to assertion		t_fault	–	–	100	us
Receiver
Centre wavelength		λC	840	850	860	nm
Receiver sensitivity @14.025G		Pmin	–	–	-10.5	dBm
Receiver sensitivity @8.5G		Pmin	–	–	-11	dBm
Receiver sensitivity @4.25G		Pmin	–	–	-12	dBm
Output differential impedance		RIN	90	100	110	Ω
Receiver overload		Pmax	0	–	–	dBm
Optical return loss		ORL	–	–	-12	Db
LOS de-assert		LOSD	–	–	-12.5	dBm
LOS assert		LOSa	-25	–	–	dBm
LOS hysteresis		–	0.5	–	–	Db
LOS	High	–	2.4	–	VCC+0.3	V
	Low	–	0	–	0.4

SFP+ TRANSCEIVER ELECTRICAL PAD LAYOUT

PIN FUNCTION DEFINITIONS

Pin	Name	Function	Plug Seq.	Notes
1	VeeT	Transmitter ground	1	Note 1
2	TX Fault	Transmitter fault indication	3	Note 2, module disables on high or open
3	TX Disable	Transmitter disable	3	Data line for serial ID
4	SDA	Module definition 2	3	Clock line for serial ID.
5	SCL	Module definition 1	3	Note 3
6	MOD-ABS	Module definition 0	3	Open or low = 8.5 or 4.25 Gb/s fibre channel(low bandwidth) High =14.025 Gb/s fibre channel (high bandwidth)
7	RS0	RX rate select(LVTTL).	3	Note 4
8	LOS	Loss of signal	3	Open or low = 8.5 or 4.25 Gb/s fibre channel(low bandwidth) High =14.025 Gb/s fibre channel (high bandwidth)
9	RS1	TX rate select(LVTTL).	1	Note 5
10	VeeR	Receiver ground	1	Note 5
11	VeeR	Receiver ground	1	Note 6
12	RD-	Inv. received data out	3	Note 6
13	RD+	Received data out	3	Note 5
14	VeeR	Receiver ground	1	3.3V ± 5%, Note 7
15	VccR	Receiver power	2	3.3V ± 5%, Note 7
16	VccT	Transmitter power	2	Note 5
17	VeeT	Transmitter ground	1	Note 8
18	TD+	Transmit data in	3	Note 8
19	TD-	Inv. transmit data in	3	Note 5
20	VeeT	Transmitter ground	1	Note 5
Notes: 1) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT/R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.2) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7K~10 K Ω resistor. Its states are: Low (0 – 0.8V): Transmitter on (>0.8, < 2.0V): Undefined High (2.0 – 3.465V): Transmitter Disabled Open: Transmitter Disabled3) Module Absent, connected to VeeT or VeeR in the module.4) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K –10KΩ resistor on host board. Pull up voltage between 2.0V and VccT/R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. 5) The module signal ground contacts, VeeR and VeeT, should be isolated from the module case. 6) RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 370 and 700 Mv differential (185–350Mv single ended) when properly terminated. 7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP+ connector pin. Maximum supply current is 300mA. Recommended host board power supply filtering is shown below. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP+ input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP+ transceiver module will result in an inrush current of no more than 30Ma greater than the steady state value. VccR and VccT may be internally connected within the SFP+ transceiver module. 8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board.

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 16G SR SFP+ 850nm 100m DOM Duplex LC MMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 10G DWDM 50GHz ZR SFP+ 80km DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Fri, 14 Nov 2025 09:26:07 +0000

SPECIFICATIONS
Product Model	SFP+10-50DW-80(ZR)-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate	11.3Gbps	Channel Data Rate	10.3125Gbps
Effective Transmission Distance	80km
Wavelength	1529.16~1567.13nm（（Tunable）;1563.86nm-1528.77nm	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	Monolithic MZM Tunable TOSA	Receiver Type	APD
TX Power	-1~3dBm,-1~4dBm;0~5dBm	Receiver Sensitivity	-23dBm
Digital Diagnostic Monitoring(DDM)	YES	Receiver Overload	-7dBm
Power Consumption	C<2.0W,I<2.5W;C<1.65W	Protocols	SFF-8431 SFF-8472 SFF-8690 ITU-T G.698.1
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Industrial)	-40℃~+85℃	Storage Temperature(Industrial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 10G 50GHz DWDM 80km ZR LC DX transceiver is a high-performance cost-effective solution supporting multi-rate data transmission from 9.95Gbps to 11.3Gbps with CDR and 8.5Gbps bypassing CDR, delivering 80km transmission over single-mode fiber (SMF); featuring dual-section design with transmitter integrating laser driver/TTOSA and receiver combining APD photodiode with transimpedance amplifier (TIA); hot-pluggable into 20-pin connector with high-speed electrical interface based on low-voltage logic, 100-ohm differential impedance and AC coupling; TX_DIS disables optical output via LVTTL high-level input, Tx_Fault signals laser/safety issues, and RX_LOS indicates incoming optical signal loss; equipped with serial EEPROM supporting monitoring/configuration via 2-wire SFP management interface, with memory organized into lower area storing basic digital diagnostic (DD) data and upper area housing specific data in high-memory tables.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

Absolute Maximum Ratings
Parameter	Symbol	Min.	Max.	Unit	Notes
Storage temperature	Ts	-40	85	℃	–
Supply voltage	Vcc3	0	3.63	V	–
Relative humidity	RH	5	+85	%	Note1
Notes: [1] Non-condensing state.

Recommended Operating Conditions
Parameter	Symbol	Min.	Typ.	Max.	Unit	Notes
Operating case temperature	Tc	-5	25	85	°C	–
Supply voltage	Vcc	3.13	3.3	3.47	V	–
Power consumption	P	–	–	2.5	W	–
Data rate	–	8.5	10.3125	11.3	Gbps	–
Transmission distance	–	–	–	80	km	–

Transmitter Operating Characteristic-Optical, Electrical
Parameter	Symbol	Min.	Typical	Max	Unit	Note
Data rate	DR	8.5	10.3125	11.3	Gbps	–
Center wavelength	CW	191.30	–	196.05	THz	–
Wavelength range	λC	1529.16	–	1567.13	nm	–
Center frequqncy variation	CFV	–	–	+/-2.5	GHz	–
-20dB spectral width	Δλ20	–	–	0.3	nm	–
Side mode suppression ratio	SMSR	30	–	–	nm	–
Laser off power	Poff	–	–	-30	dBm	–
Optical eye mask	EMM	5	–	–	%	–
Average optical power	PO	-1	–	3	dBm	–
Extinction ratio	ER	8.2	–		dB	–
Cross point of eye	CP	40	–	52	%	–
Transmitter dispersion renalty	TDP	–	–	2	dB	–
Relative intensity noise	RIN 12OMA	–	–	-128	dB/Hz	–
Optical eye mask	ORLT	–	–	-27	dB	–
Tx Input diff voltage	VI	200	–	700	mV	–

Receiver Operating Characteristic-Optical, Electrical
Parameter	Symbol	Min.	Typical	Max.	Unit	Note
Data rate	DR	8.5	10.3125	11.3	Gbps	–
Center wavelength	CW	1260	–	1600	nm	–
Sensitivity @(BER=1E-12, PRBS 2^31-1, NRZ, 9.95Gbps~10.7Gbps data rate	Psen	–	–	-23	dBm	–
Sensitivity @(BER=1.0E-04, PRBS 2^31- 1, NRZ,11.3Gbps data rate)	Psen	–	–	-26	dBm	–
B2B OSNR Tolerance @ 1E-4	–	–	–	16	dB	–
Input optical power(no damaged)	IOP	4	–	–	dBm	–
Saturation power（EOL）	SP	-7	–	–	dBm	–
Loss of signal – asserted	LosA	-35	–	–	dBm	–
Loss of signal- deasserted	LosD	–	–	-28	dBm	–
Hysteresis	LosH	0.5	–	–	dB	–
Rx output diff voltage	Vo	250	–	850	mV	–
Loss of signal voltage	VOH	Vcc-0.5	–	Vcc+0.3	V	–
Loss of signal voltage	VOL	0	–	0.4	V	–

Digital Diagnostic Functions
Parameter	Symbol	Min.	Typical	Max	Units	Notes
Temperature monitor absolute error	DMI_Temp	-3	–	3	℃	Over operating temperature
Supplyvoltage monito rabsolute error	DMI_Vcc	-3%	–	3%	V	–
Bias current monitor absolute error	DMI_Ibias	-10%	–	10%	mA	–
Lase rpower monitor absolute error	DMI_Tx	-3	–	3	dB	–
RX power monitor absolute error	DMI_Rx	-3	–	3	dB	–

Control and StatusI/OTiming Characteristics
Parameter	Symbol	Min.	Typical	Max	Units	Notes
TX disable assert time	t_off	–	–	100	µs	Note1
TX disable negate time	t_on	–	–	2	ms	Note2
Time to initialize including reset of TX_fault	t_init	–	–	300	ms	Note3
Time to initialize cooled module and time to power up a cooled module to power level II	t_start_up_co oled	–	–	90	s	Note4
TX fault assert time	t_fault_on	–	–	1	ms	Note5
TX fault reset time	t_reset	10	–	–	µs	Note6
LOS assert time	t_loss_on	–	–	100	µs	Note7
LOS deassert time	t_loss_off	–	–	100	µs	Note8
Notes: [1] Time from rising edge of TX Disable to when the optical output falls below 10% of nominal. [2] Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal. [3] From power on or negation of TX Fault using TX Disable. [4] From power supply or hot plug or TX Disable negated during power up, or TX Fault recovery, until cooled power level I part (or cooled power level II part during Fault recovery) the SFP+ is fully operational [5] Time from fault to TX fault on. [6] Time from TX fault to TX nominal. [7] Time from LOS state to RX LOS assert. [8] Time from non-LOS state to RX LOS deassert.

PIN-OUT DEFINITIONS

	Logic	Symbol	Name/Description	Note
1	–	VeeT	Module transmitter ground	Note1
2	LVTTL-O	TX_fault	Module transmitter fault	Note2
3	LVTTL-I	TX_disable	Transmitter disable;Turnsofftrans mitterlaseroutput	Note3
4	LVTTL-I/O	SDA	2-Wire serial interface data line(Same as MOD-DEF2 asdefinedin the INF-8074i)	Note4
5	LVTTL-I/O	SCL	2-Wire serial interface clock(Same as MOD-DEF1 as defined intheINF-8074i)	Note4
6	–	MOD-ABS	Module absent, connected to VeeT or VeeR in the module	Note5
7	LVTTL-I	RS0	Rate select 0	–
8	LVTTL-O	RX_LOS	Receiver Loss of Signal indication (In FC designated as RX_LOS, in SONET designated as LOS, and in ethernet designated at signal detect)	Note2
9	LVTTL-I	RS1	Rate select 1	–
10	–	VeeR	Module receiver ground	Note1
11	–	VeeR	Module receiver ground	Note1
12	CML-O	RD-	Receiver inverted data output	–
13	CML-O	RD+	Receiver non inverted data output	–
14	–	VccR	Module receiver ground	Note1
15	–	VeeR	Module receiver 3.3 V supply	–
16	–	VccT	Module transmitter 3.3 V supply	Note1
17	–	VeeT	Module transmitter ground	–
18	CML- I	TD+	Transmitter non-inverted data input	–
19	CML- I	TD-	Transmitter inverted data input	–
20	–	VeeT	Module yransmitter ground	Note1
Notes: [1]The module signal ground pins, VeeR and VeeT, shall be isolated from the module case.[2]This pin is an open collector/drain output pin and shall be pulled up with 4.7k-10kohms to Host_Vcc on the host board. Pull ups can be connected to multiple power supplies, however the host board design shall ensure that no module pin has voltage exceeding module VccT/R + 0.5 V.[3]This pin is an open collector/drain input pin and shall be pulled up with 4.7k-10kohms to VccT in the module. [4]See SFF-8431 4.2 2-wire Electrical Specifications. [5]This pin shall be pulled up with 4.7k-10kohms to Host_Vcc on the host board

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 10G DWDM 50GHz ZR SFP+ 80km DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 10G DWDM 50GHz ER SFP+ 40km DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Fri, 14 Nov 2025 08:23:18 +0000

SPECIFICATIONS
Product Model	SFP+10-50DW-40(ER)-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate	11.3Gbps	Channel Data Rate	10.3125Gbps
Effective Transmission Distance	40km
Wavelength	1529.16~1567.13nm（Tunable）	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	Monolithic MZM Tunable TOSA	Receiver Type	PIN
TX Power	-1~3dBm,-1~4dBm	Receiver Sensitivity	-16dBm
Digital Diagnostic Monitoring(DDM)	YES	Receiver Overload	-1dBm
Power Consumption	C<2.1W,I<2.5W	Protocols	SFF-8431 SFF-8472 SFF-8690 IEEE 802.3ae CL 52
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Industrial)	-40℃~+85℃	Storage Temperature(Industrial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 10G 50GHz DWDM 40km ER LC DX is a high performance, cost effective module supporting multi rate 9.95Gbps to 11.3Gbps with CDR, 8.5Gbps bypass CDR, and transmission distance up to 40km on SM fiber; the transceiver consists of two sections: transmitter incorporating a laser driver and TTOSA, and receiver with PIN integrated transimpedance preamplifier (TIA); this hot-pluggable module connects via 20-pin connector, featuring high-speed electrical interface based on low voltage logic with nominal 100ohms differential impedance and AC coupling; optical output is disabled by LVTTL high-level TX_DIS input, while Tx_Fault indicates laser-related faults and RX_LOS signals receiver input loss; its serial EEPROM enables monitoring/configuration access via 2-wire SFP management interface using single address A0h, with memory map divided into lower area (storing basic DD data) and upper area housing specific data in high memory tables.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

Absolute Maximum Ratings
Parameter	Symbol	Min.	Max.	Unit	Notes
Storage temperature	Ts	-40	85.0	℃	–
Power supply voltage	Vcc3	0	3.63	V	–
Relative humidity(noncondensation)	RH	5	+85	%	Note1
Damage threshold	Pmax	–	–	dBm	–

Recommended Operating Conditions
Parameter	Symbol	Min.	Typ.	Max.	Unit	Notes
Operating case temperature	Tc	0	25	75	°C	–
Supply voltage	Vcc	3.13	3.3	3.47	V	–
Power supply current	Pd	–	–	670	mA	–
Data rate	–	8.5	10.3125	11.3	Gbps	–
Transmission distance	–	–	–	40	km	–

Transmitter Operating Characteristic-Optical, Electrical
Parameter	Symbol	Min.	Typical	Max	Unit	Note
Data rate	DR	8.5	10.3125	11.3	Gbps	–
Center wavelength	CW	191.3	–	196.05	THz	–
Wavelength range	λC	1529.16	–	1567.13	nm	–
Center frequqncy variation	CFV	0	–	+/-2.5	GHz	–
-20dB spectral width	Δλ20	–	–	0.3	nm	–
Side mode suppression ratio	SMSR	30	–	–	nm	–
Laser off power	Poff	–	–	-30	dBm	–
Transmitter reflectance	TR	–	–	-12	dB	–
Average optical power	PO	-1	0.5	3	dBm	–
Extinction ratio	ER	8.2	–		dB	–
Cross point of eye	CP	0.4	–	0.52		–
Transmitter dispersion renalty	TDP		–	3	dB	–
Transmitter dispersion tolerance(CD window with 2dB OSNR penalty)	TDT	-700	–	700	km ps/nm	–
Relative intensity noise	RIN12OMA	–	–	-128	dB/Hz	–
Optical eye mask	EMM	5	–	–	–	–
Tx Input diff voltage	VI	200	–	850	mV	–

Receiver Operating Characteristic-Optical, Electrical
Parameter	Symbol	Min.	Typical	Max.	Unit	Note
Data rate	DR	8.5	10.3125	11.3	Gbps	–
Center wavelength	CW	1260	–	1600	nm	–
Sensitivity @(BER=1E-12, PRBS 2^31-1, NRZ, 9.95Gbps~10.7Gbps data rate	Psen	1529.16	–	-16(EOL)	dBm	–
Sensitivity @(BER=2.0E-03, PRBS 2^31-1,NRZ,11.3Gbps data rate, dispersion 800ps/nm, at room temperature and OSNR >31dB)	Psen	–	–	-19 (EOL)	dBm	–
B2B OSNR Tolerance BOL @ 2E-3 Test condition： A:optical filter type and bandwidth：flattop filter -3dB bandwidth 84 GHz, OSA res 0.1nm for noise bandwidth. B: Input optical power range： 0~-14dBm C:9.9Gbps~11.3Gbps data rate range D:-5~70℃ E：Under the optimal threshold or 50% threshold	–	–	–	13.5	dB	–
B2B OSNR Tolerance BOL @ 2E-3 Test condition： A:optical filter type and bandwidth：flattop filter -3dB bandwidth 84 GHz, OSA res 0.1nm for noise bandwidth. B: Input optical power range： 0~-14dBm C:9.9Gbps~11.3Gbps data rate range D:-5~70℃ E：Under the optimal threshold or 50% threshold	–	–	–	14.0	dB	–
Saturation power（EOL）	SP	-1	–	–	dBm	–
Input optical power(no	IOP	4	–	–	dBm	–

Receiver Operating Characteristic-Optical, Electrical
Parameter	Symbol	Min.	Typical	Max.	Unit	Note
Data rate	DR	8.5	10.3125	11.3	Gbps	–
Center wavelength	CW	1260	–	1600	nm	–
Sensitivity @(BER=1E-12, PRBS 2^31-1, NRZ, 9.95Gbps~10.7Gbps data rate	Psen	1529.16	–	-16(EOL)	dBm	–
Sensitivity @(BER=2.0E-03, PRBS 2^31-1,NRZ,11.3Gbps data rate, dispersion 800ps/nm, at room temperature and OSNR >31dB)	Psen	–	–	-19 (EOL)	dBm	–
B2B OSNR Tolerance BOL @ 2E-3 Test condition： A:optical filter type and bandwidth：flattop filter -3dB bandwidth 84 GHz, OSA res 0.1nm for noise bandwidth. B: Input optical power range： 0~-14dBm C:9.9Gbps~11.3Gbps data rate range D:-5~70℃ E：Under the optimal threshold or 50% threshold	–	–	–	13.5	dB	–
B2B OSNR Tolerance BOL @ 2E-3 Test condition： A:optical filter type and bandwidth：flattop filter -3dB bandwidth 84 GHz, OSA res 0.1nm for noise bandwidth. B: Input optical power range： 0~-14dBm C:9.9Gbps~11.3Gbps data rate range D:-5~70℃ E：Under the optimal threshold or 50% threshold	–	–	–	14.0	dB	–
Saturation power（EOL）	SP	-1	–	–	dBm	–
Input optical power(no	IOP	4	–	–	dBm	–

Digital Diagnostic Functions
Parameter	Symbol	Min.	Typical	Max	Units	Notes
Temperature monitor absolute error	DMI_Temp	-3	–	3	℃	Over operating temperature
Supplyvoltage monito rabsolute error	DMI_Vcc	-3%	–	3%	V	Over operating voltage
Bias current monitor absolute error	DMI_Ibias	-10%	–	10%	mA	–
Lase rpower monitor absolute error	DMI_Tx	-3	–	3	dB	–

Control and StatusI/OTiming Characteristics
Parameter	Symbol	Min.	Typical	Max	Units	Notes
TX disable assert time	t_off	–	–	100	µs	Note1
TX disable negate time	t_on	–	–	2	ms	Note2
Time to initialize including reset of TX_fault	t_init	–	–	300	ms	Note3
TX fault assert time	t_fault_on	–	–	1	ms	Note4
TX fault reset time	t_reset	10	–	–	µs	Note5
LOS assert time	t_loss_on	–	–	100	µs	Note6
LOS deassert time	t_loss_off	–	–	100	µs	Note7
Notes: [1]Time from rising edge of TX Disable to when the optical output falls below 10% of nominal. [2]Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal. [3]From power on or negation of TX Fault using TX Disable. [4]Time from fault to TX fault on. [5]Time from TX fault to TX nominal. [6]Time from LOS state to RX LOS assert. [7]Time from non-LOS state to RX LOS deassert.

PIN-OUT DEFINITIONS

	Logic	Symbol	Name/Description	Note
1	–	VeeT	Module transmitter ground	Note1
2	LVTTL-O	TX_fault	Module transmitter fault	Note2
3	LVTTL-I	TX_disable	Transmitter disable;Turnsofftrans mitterlaseroutput	Note3
4	LVTTL-I/O	SDA	2-Wire serial interface data line(Same as MOD-DEF2 asdefinedin the INF-8074i)	Note4
5	LVTTL-I/O	SCL	2-Wire serial interface clock(Same as MOD-DEF1 as defined intheINF-8074i)	Note4
6	–	MOD-ABS	Module absent, connected to VeeT or VeeR in the module	Note5
7	LVTTL-I	RS0	Rate select 0	–
8	LVTTL-O	RX_LOS	Receiver Loss of Signal indication (In FC designated as RX_LOS, in SONET designated as LOS, and in ethernet designated at signal detect)	Note2
9	LVTTL-I	RS1	Rate select 1	–
10	–	VeeR	Module receiver ground	Note1
11	–	VeeR	Module receiver ground	Note1
12	CML-O	RD-	Receiver inverted data output	–
13	CML-O	RD+	Receiver non inverted data output	–
14	–	VccR	Module receiver ground	Note1
15	–	VeeR	Module receiver 3.3 V supply	–
16	–	VccT	Module transmitter 3.3 V supply	Note1
17	–	VeeT	Module transmitter ground	–
18	CML- I	TD+	Transmitter non-inverted data input	–
19	CML- I	TD-	Transmitter inverted data input	–
20	–	VeeT	Module yransmitter ground	Note1
Notes: [1]The module signal ground pins, VeeR and VeeT, shall be isolated from the module case.[2]This pin is an open collector/drain output pin and shall be pulled up with 4.7k-10kohms to Host_Vcc on the host board. Pull ups can be connected to multiple power supplies, however the host board design shall ensure that no module pin has voltage exceeding module VccT/R + 0.5 V.[3]This pin is an open collector/drain input pin and shall be pulled up with 4.7k-10kohms to VccT in the module.[4]See SFF-8431 4.2 2-wire Electrical Specifications. [5]This pin shall be pulled up with 4.7k-10kohms to Host_Vcc on the host board

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 10G DWDM 50GHz ER SFP+ 40km DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 10G DWDM 100GHz ZR SFP+ 80km DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Fri, 14 Nov 2025 07:47:55 +0000

SPECIFICATIONS
Product Model	SFP+10-100DW-80(ZR)-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate	11.3Gbps	Channel Data Rate	10.5Gbps
Effective Transmission Distance	80km
Wavelength	1528.77nm to 1563.86nm	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	DWDM EML	Receiver Type	IDP
TX Power	0~4dBm	Receiver Sensitivity	-23dBm
Digital Diagnostic Monitoring(DDM)	YES	Receiver Overload	-7dBm
Power Consumption	C<1.5W,I<1.8W	Protocols	SFF-8431 MSA SFF-8432 MSA
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Industrial)	-40℃~+85℃	Storage Temperature(Industrial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 10G 100GHz DWDM 80km ZR LC DX series single-mode transceiver is a compact, pluggable module designed for duplex optical data communications. Tailored for DWDM networking equipment in metropolitan access and core networks, this module operates across nominal DWDM wavelengths from 1528nm to 1566nm, as specified by ITU-T standards. It is fully compliant with the SFF-8431 and SFF-8432 MSA specifications.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

General Specifications
Parameter	Symbol	Min	Typ.	Max	Unit	Ref.
Module form factor	BR	9.95	–	10.5	Gb/s	1
Number of lanes	BER	–	–	10-12	–	2
Maximum aggregate data rate	Lmax	–	80	–	km	–
*Notes: 1. 10GBASE-ZR, 10GBASE-ZW, 1200-SM-LL-L 10GFC. 2. Tested with a PRBS 231-1 test pattern

Absolute Maximum Ratings
Parameter	Symbol	Min.	Typ.	Max.	Unit
Storage temperature	Ts	-40	–	85	°C
Supply voltage	Vcc	-0.5	–	4	V
Operating relative humidity	–	–	–	85	%

Electrical Characteristics
Parameter		Symbol	Min.	Typ.	Max	Unit	Notes
Power supply voltage		Vcc	3.15	3.3	3.45	V	–
Power supply current		Icc (0℃ to 70℃)	–	350	455	mA	–
		Icc (-40℃ to 85℃)	–	350	545	mA	–
Date rate		DR	0.6	–	11.3	Gbps	Date rate
Transmitter
TX_dis	Disable	–	2	–	Vcc+0.3	V	–
	Enable	–	0	–	0.8		–
TX_FAULT	Fault	–	2	–	Vcc+0.3	V	–
	Normal	–	0	–	0.5		–
CML inputs (Differential)		Vin	250		1000	mVpp	AC coupled input
Input impedance (Differential)		Zin	85	100	115	ohm	Rin > 100 kohm @ DC
Receiver
CML Outputs (Differential)		Vout	350	–	700	mVpp	AC coupled outputs
RX_LOS	Loss	–	2	–	Vcc+0.3	V	–
	Normal	–	0	–	0.8		–
Output impedance (Differential)		Zout	85	100	115	ohm	–
MOD_DEF ( 0:2 )		VoH	2.5	–	–	V	With serial ID
		VoL	0	–	0.5	V

Optical Characteristics
Parameter	Symbol	Min.	Typ.	Max.	Unit
Data rate	–	0.6	–	11.3	Gbps
Transmitter
Side mode suppression ratio	SMSR	30	–	–	dB
Center wavelength spacing	–	–	100	–	GHz
	–		0.8	–	nm
Average output power	Pout	0	–	4	dBm
Average launch power (Tx: OFF)	POFF	–	–	-30	dBm
Extinction ratio	ER	6	–	–	dB
Transmitter dispersion penalty @1600ps/nm	TDP	–	–	3	dB
Pout@TX disable asserted	Pout	–	–	-45	dBm
Relative intensity noise	RIN	–	–	-128	dB/Hz
TX jitter	TXj	Per 802.3ae requirements
Receiver
Receiver sensitivity	Pmin	–	–	-23	dBm
Receiver overload	Pmax	-7	–	–	dBm
LOS de-assert	LOSD	–	–	-24	dBm
LOS assert	LOSA	-40	–	–	dBm
LOS hysteresis	–	0.5	–	–	dB
Notes: 1. Output is coupled into a 9/125μm single-mode fiber. 2. Minimum average optical power measured at the BER less than 1E-12. The measurepattern is PRBS 231-1. 3. CML logic, internally AC coupled.

Wavelength Table
Channel	Frequency (THz)	Center wavelength(nm)	Channel	Frequency (THz)	Center wavelength(nm)
17	191.7	1563.86	40	194	1545.32
18	191.8	1563.05	41	194.1	1544.53
19	191.9	1562.23	42	194.2	1543.73
20	192	1561.41	43	194.3	1542.94
21	192.1	1560.61	44	194.4	1542.14
22	192.2	1559.79	45	194.5	1541.35
23	192.3	1558.98	46	194.6	1540.56
24	192.4	1558.17	47	194.7	1539.77
25	192.5	1557.36	48	194.8	1538.98
26	192.6	1556.55	49	194.9	1538.19
27	192.7	1555.75	50	195	1537.4
28	192.8	1554.94	51	195.1	1536.61
29	192.9	1554.13	52	195.2	1535.82
30	193	1553.33	53	195.3	1535.04
31	193.1	1552.52	54	195.4	1534.25
32	193.2	1551.72	55	195.5	1533.47
33	193.3	1550.92	56	195.6	1532.68
34	193.4	1550.12	57	195.7	1531.9
35	193.5	1549.32	58	195.8	1531.12
36	193.6	1548.51	59	195.9	1530.33
37	193.7	1547.72	60	196	1529.55
38	193.8	1546.92	61	196.1	1528.77
39	193.9	1546.12	–	–	–

PIN DESCRIPTION

Pin	Name	Function	Plug Seq.	Notes
1	VeeT	Transmitter ground	1	Note 5
2	TX Fault	Transmitter fault indication	3	Note 1
3	TX Disable	Transmitter disable	3	Note 2, module disables on high or open
4	SDA	Module definition 2	3	Note 3, data line for serial ID.
5	SCL	Module definition 1	3	Note 3, clock line for serial ID.
6	MOD-ABS	Module definition 0	3	Note 3
7	RS0	RX rate select(LVTTL).	3	Rate select 0, optionally controls SFP+ module receiver. This pin is pulled low to VeeT with a>30K resistor.
8	LOS	Loss of signal	3	Note 4
9	RS1	TX rate select(LVTTL).	1	Rate select 1, optionally controls SFP+ module transmitter. This pin is pulled low to VeeT with a >30K resistor.
10	VeeR	Receiver ground	1	Note 5
11	VeeR	Receiver ground	1	Note 5
12	RD-	Inv. received data out	3	Note 6
13	RD+	Received data out	3	Note 7
14	VeeR	Receiver ground	1	Note 5
15	VccR	Receiver power	2	3.3V ± 5%, Note 7
16	VccT	Transmitter power	2	3.3V ± 5%, Note 7
17	VeeT	Transmitter ground	1	Note 5
18	TD+	Transmit data in	3	Note 8
19	TD-	Inv. transmit data in	3	Note 8
20	VeeT	Transmitter ground	1	Note 5
Notes: 1) . TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10K resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high,output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.2) . TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7-10 K resistor. Its states are: Low (0 – 0.8V): Transmitter on (>0.8, < 2.0V): Undefined High (2.0 – 3.465V):Transmitter Disabled Open: Transmitter Disabled3)Module absent, connected to VEET or VEER in the module.4) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K–10K resistor. Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.5) VeeR and VeeT may be internally connected within the SFP+ module. 6) RD-/+: These are the differential receiver outputs. They are AC coupled 100 differential lines which should be terminated with100(differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. 7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP+ connector pin. Maximum supply current is 300mA. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP+ input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP+ transceiver module will result in an inrush current of no more than 30mA greater than the steady state value. VccR and VccT may be internall connected within the SFP+ transceiver module. 8) . TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100 differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board.

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 10G DWDM 100GHz ZR SFP+ 80km DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 10G DWDM 100GHz ER SFP+ 40km DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Fri, 14 Nov 2025 07:12:23 +0000

SPECIFICATIONS
Product Model	SFP+10-100DW-40(ER)-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate	11.3Gbps	Channel Data Rate	10.5Gbps
Effective Transmission Distance	40km
Wavelength	1528.77nmto1563.86nm	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	DWDM EML	Receiver Type	IDP
TX Power	-1~4dBm	Receiver Sensitivity	-16dBm
Digital Diagnostic Monitoring(DDM)	YES	Receiver Overload	0dBm
Power Consumption	C<1.5W,I<1.8W	Protocols	SFF-8431 MSA SFF-8432 MSA SFF 8472
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Industrial)	-40℃~+85℃	Storage Temperature(Industrial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 10G 100GHz DWDM 40km ER LC DX series single-mode transceiver is a compact pluggable module designed for duplex optical data communications. Ideal for deployment in DWDM networking equipment within metropolitan access and core networks, this module operates at nominal DWDM wavelengths from 1528nm to 1566nm, in accordance with ITU-T specifications. It is fully compliant with SFF-8431 and SFF-8432 MSA standards.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

General Specifications
Parameter	Symbol	Min	Typ.	Max	Unit	Ref.
Module form factor	BR	9.95	–	10.5	Gb/s	1
Number of lanes	BER	–	–	10-12	–	2
Maximum aggregate data rate	Lmax	–	40	–	km	–
*Notes: 1. 10GBASE-ER, 10GBASE-EW, 1200-SM-LL-L 10GFC. 2. Tested with a PRBS 231-1 test pattern.

Absolute Maximum Ratings
Parameter	Symbol	Min.	Typ.	Max.	Unit
Storage temperature	Ts	-40	–	85	°C
Supply voltage	Vcc	-0.5	–	4	V
Operating relative humidity	–	–	–	85	%

Recommended Operating Conditions
Parameter	Symbol	Min.	Typical	Max.	Unit
Case operating temperature	TC	-5	–	+70	°C
Supply voltage	Vcc	3.15	3.3	3.45	V
Supply current	Icc	–	–	430	mA
Data rate	–	0.614	–	11.3	Gbps

Electrical Characteristics
Parameter		Symbol	Min.	Typ.	Max	Unit	Notes
Power supply voltage		Vcc	3.15	3.3	3.45	V	–
Power supply current		Icc (0℃ to 70℃)	–	350	455	mA	–
		Icc (-40℃ to 85℃)	–	350	545	mA	–
Date rate		DR	0.6	–	11.3	Gbps	Date rate
Transmitter
TX_dis	Disable	–	2	–	Vcc+0.3	V	–
	Enable	–	0	–	0.8		–
TX_FAULT	Fault	–	2	–	Vcc+0.3	V	–
	Normal	–	0	–	0.5		–
CML inputs (Differential)		Vin	250		1000	mVpp	AC coupled input
Input impedance (Differential)		Zin	85	100	115	ohm	Rin > 100 kohm @ DC
Receiver
CML Outputs (Differential)		Vout	350	–	700	mVpp	AC coupled outputs
RX_LOS	Loss	–	2	–	Vcc+0.3	V	–
	Normal	–	0	–	0.8		–
Output impedance (Differential)		Zout	85	100	115	ohm	–
MOD_DEF ( 0:2 )		VoH	2.5	–	–	V	With serial ID
		VoL	0	–	0.5	V

Optical Characteristics
Parameter	Symbol	Min.	Typ.	Max.	Unit
Data rate	–	0.6	–	11.3	Gbps
Transmitter
Side mode suppression ratio	SMSR	30	–	–	dB
Center wavelength spacing	–	–	100	–	GHz
	–		0.8	–	nm
Average output power	Pout	-1	–	4	dBm
Average launch power (Tx: OFF)	POFF	–	–	-30	dBm
Extinction ratio	ER	6	–	–	dB
Transmitter dispersion penalty @800ps/nm	TDP	–	–	3.0	dB
Pout@TX disable asserted	Pout	–	–	-45	dBm
Relative intensity noise	RIN	–	–	-128	dB/Hz
TX jitter	TXj	Per 802.3ae requirements
Receiver
Receiver sensitivity	Pmin	–	–	-16	dBm
Receiver overload	Pmax	0	–	–	dBm
LOS de-assert	LOSD	–	–	-17	dBm
LOS assert	LOSA	-30	–	–	dBm
LOS hysteresis	–	0.5	–	–	dB
*Notes: 1. Output is coupled into a 9/125μm single-mode fiber. 2. Minimum average optical power measured at the BER less than 1E-12. The measurepattern is PRBS 231-1. 3. CML logic, internally AC coupled.

Wavelength Table
Channel	Frequency (THz)	Center wavelength(nm)	Channel	Frequency (THz)	Center wavelength(nm)
17	191.7	1563.86	40	194	1545.32
18	191.8	1563.05	41	194.1	1544.53
19	191.9	1562.23	42	194.2	1543.73
20	192	1561.41	43	194.3	1542.94
21	192.1	1560.61	44	194.4	1542.14
22	192.2	1559.79	45	194.5	1541.35
23	192.3	1558.98	46	194.6	1540.56
24	192.4	1558.17	47	194.7	1539.77
25	192.5	1557.36	48	194.8	1538.98
26	192.6	1556.55	49	194.9	1538.19
27	192.7	1555.75	50	195	1537.4
28	192.8	1554.94	51	195.1	1536.61
29	192.9	1554.13	52	195.2	1535.82
30	193	1553.33	53	195.3	1535.04
31	193.1	1552.52	54	195.4	1534.25
32	193.2	1551.72	55	195.5	1533.47
33	193.3	1550.92	56	195.6	1532.68
34	193.4	1550.12	57	195.7	1531.9
35	193.5	1549.32	58	195.8	1531.12
36	193.6	1548.51	59	195.9	1530.33
37	193.7	1547.72	60	196	1529.55
38	193.8	1546.92	61	196.1	1528.77
39	193.9	1546.12	–	–	–

PIN DESCRIPTION

Pin	Name	Function	Plug Seq.	Notes
1	VeeT	Transmitter ground	1	Note 5
2	TX Fault	Transmitter fault indication	3	Note 1
3	TX Disable	Transmitter disable	3	Note 2, module disables on high or open
4	SDA	Module definition 2	3	Note 3, data line for serial ID.
5	SCL	Module definition 1	3	Note 3, clock line for serial ID.
6	MOD-ABS	Module definition 0	3	Note 3
7	RS0	RX rate select(LVTTL).	3	Rate select 0, optionally controls SFP+ module receiver. This pin is pulled low to VeeT with a>30K resistor.
8	LOS	Loss of signal	3	Note 4
9	RS1	TX rate select(LVTTL).	1	Rate select 1, optionally controls SFP+ module transmitter. This pin is pulled low to VeeT with a >30K resistor.
10	VeeR	Receiver ground	1	Note 5
11	VeeR	Receiver ground	1	Note 5
12	RD-	Inv. received data out	3	Note 6
13	RD+	Received data out	3	Note 7
14	VeeR	Receiver ground	1	Note 5
15	VccR	Receiver power	2	3.3V ± 5%, Note 7
16	VccT	Transmitter power	2	3.3V ± 5%, Note 7
17	VeeT	Transmitter ground	1	Note 5
18	TD+	Transmit data in	3	Note 8
19	TD-	Inv. transmit data in	3	Note 8
20	VeeT	Transmitter ground	1	Note 5
Notes: 1) . TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10K resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high,output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.2) . TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7-10 K resistor. Its states are: Low (0 – 0.8V): Transmitter on (>0.8, < 2.0V): Undefined High (2.0 – 3.465V):Transmitter Disabled Open: Transmitter Disabled3)Module absent, connected to VEET or VEER in the module.4) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K–10K resistor. Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. 5) VeeR and VeeT may be internally connected within the SFP+ module. 6) RD-/+: These are the differential receiver outputs. They are AC coupled 100 differential lines which should be terminated with100(differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. 7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP+ connector pin. Maximum supply current is 300mA. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP+ input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP+ transceiver module will result in an inrush current of no more than 30mA greater than the steady state value. VccR and VccT may be internall connected within the SFP+ transceiver module. 8) . TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100 differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board.

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 10G DWDM 100GHz ER SFP+ 40km DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 10G CWDM(1470-1610nm) ZR SFP+ DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Fri, 14 Nov 2025 06:30:57 +0000

SPECIFICATIONS
Product Model	SFP+10-CW1416-ZR-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate	11.3Gbps	Channel Data Rate	10.138Gb/s
Power Budget	23dB
Wavelength	1470nm to 1610nm	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	CWDM EML	Receiver Type	IDP
TX Power	0~4dBm	Receiver Sensitivity	-23dBm
Digital Diagnostic Monitoring(DDM)	YES	Receiver Overload	-8dBm
Power Consumption	<1.5W	Protocols	SFF-8431 SFF-8432 SFF-8472
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Extended)	-20℃~+75℃	Storage Temperature(Industrial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 10G CWDM (1470-1610nm) ZR LC DX series optical transceiver is designed for high-performance fiber communication applications up to 10G, fully compliant with the SFP+ MSA SFF-8431 specification. This module is optimized for single-mode fiber and operates at CWDM wavelengths, offering eight center wavelengths from 1470nm to 1610nm, with 20nm increments between each wavelength. It provides a guaranteed optical link budget of 23dB. The module features an SFP+ connector for hot-plug capability and requires a single 3.3V power supply. The optical output can be disabled via an LVTTL logic high-level input (TX_DIS), and a Loss of Signal (RX_LOS) output is available to indicate the absence of an optical signal at the receiver. Additionally, this module supports digital diagnostic functions through a 2-wire serial interface, in compliance with the SFF-8472 specification.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

CWDM* Wavelength
Band	Nomenclature	Wavelength(nm)
		Min.	Typ.	Max.
S-band short wavelength	K	1464	1470	1477.5
	L	1484	1490	1497.5
	M	1504	1510	1517.5
	N	1524	1530	1537.5
C-band conventional	O	1544	1550	1557.5
L-band long wavelength	P	1564	1570	1577.5
	Q	1584	1590	1597.5
	R	1604	1610	1617.5
CWDM*: 8 Wavelengths from 1470nm to 1610nm, each step 20nm.

Absolute Maximum Ratings
Parameter	Symbol	Min.	Max.	Unit
Maximum supply voltage 1	Vcc	-0.5	4.0	V
Storage temperature	Ts	-40	85	°C

Recommended Operating Conditions
Parameter	Symbol		Min.	Typical	Max.	Units
Case operating temperature	TC	Standard	0	–	+70	°C
		Extended	-20	–	+75
Supply voltage	Vcc		3.13	3.3	3.45	V
Supply current	Icc		–	–	455	mA
Data rate	SFP+10-CW1416-ZR-LCD		0.6	–	11.3	Gbps

Electrical Characteristics
Parameter	Symbol	Min.	Typ.	Max	Unit	Notes
Transmitter
CML inputs(Differential)	Vin	180	–	1000	mVpp	1
Input impedance (Differential)	Zin	85	100	115	ohms	–
Tx_DISABLE input voltage – high	–	2	–	Vcc+0.3	V	–
Tx_DISABLE input voltage – low	–	0	–	0.8	V	–
Tx_FAULT output voltage – high	–	2	–	Vcc+0.3	V	–
Tx_FAULT output voltage – low	–	0	–	0.8	V	–
Receiver
CML Outputs (Differential)	Vout	350	–	700	mVpp	1
Output impedance (Differential)	Zout	85	100	115	ohms	–
Rx_LOS output voltage – high	–	2	–	Vcc+0.3	V	–
Rx_LOS output voltage – low	–	0	–	0.8	V	–
MOD_DEF ( 0:2 )	VoH	2.5	–	–	V	2
	VoL	0	–	0.5	V
Notes: 1. After internal AC coupling. 2. Reference the SFF-8472 MSA.

Optical Characteristics
Parameter	Symbol	Min.	Typical	Max.	Unit	Note
Transmitter
Output opt. pwr: 9/125 SMF	Pout	0	–	4	dBm	1
Extinction ratio	ER	3.5	–	–	dB	–
Optical wavelength	λ	λc–6	λc	λc+7.5	nm	2
-20dB spectrum width	Δλ	–	–	1	nm	–
Side mode suppression ratio	SMSR	30	–	–	dB	–
Average launch power of OFF transmitter	POFF	–	–	-30	dBm	–
Transmitter dispersion penalty	TDP	–	–	3.5	dB	–
TX jitter	TXj	Per 802.3ae requirements			–	–
Relative intensity noise	RIN	–	–	-128	dB/Hz	–
Receiver
Receiver sensitivity	Pmin	–	–	-23	dBm	3
Input overload	Pmax	-8	–	–	dBm	–
Optical center wavelength	λ	1260	–	1620	nm	–
Receiver reflectance	Rrf	–	–	-12	dB	–
LOS de-assert	LOSD	–	–	-24	dBm	–
LOS assert	LOSA	-37	–	–	dBm	–
LOS hysteresis	–	1	–	–	dB	–
*Notes: 1. Output power is coupled into a 9/125μm SMF. 2. ITU-T G.694.2 CWDM wavelength from 1470nm to 1610nm, each step 20nm. 3. Average received power; BER less than 1E-12 and PRBS 231-1 test pattern

SFP+ TRANSCEIVER ELECTRICAL PAD LAYOUT

PIN FUNCTION DEFINITIONS

Pin	Name	Function	Plug Seq.	Notes
1	VeeT	Transmitter ground	1	Note 5
2	TX Fault	Transmitter fault indication	3	Note 1
3	TX Disable	Transmitter disable	3	Note 2, module disables on high or open
4	SDA	Module definition 2	3	2-Wire serial interface data line.
5	SCL	Module definition 1	3	2-Wire serial Interface clock.
6	MOD-ABS	Module definition 0	3	Note 3
7	RS0	RX rate select(LVTTL).	3	No function implement
8	LOS	Loss of signal	3	Note 4
9	RS1	TX rate select(LVTTL).	1	No function implement
10	VeeR	Receiver ground	1	Note 5
11	VeeR	Receiver ground	1	Note 5
12	RD-	Inv. received data out	3	Note 6
13	RD+	Received data out	3	Note 6
14	VeeR	Receiver ground	1	Note 5
15	VccR	Receiver power	2	3.3V ± 5%, Note 7
16	VccT	Transmitter power	2	3.3V ± 5%, Note 7
17	VeeT	Transmitter ground	1	Note 5
18	TD+	Transmit data in	3	Note 8
19	TD-	Inv. transmit data in	3	Note 8
20	VeeT	Transmitter ground	1	Note 5
Notes: 1) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT/R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.2) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7K~10 K Ω resistor. Its states are: Low (0 – 0.8V): Transmitter on (>0.8, < 2.0V): Undefined High (2.0 – 3.465V): Transmitter Disabled Open: Transmitter Disabled3) Module Absent, connected to VeeT or VeeR in the module. 4) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K –10KΩ resistor on host board. Pull up voltage between 2.0V and VccT/R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. 5) The module signal ground contacts, VeeR and VeeT, should be isolated from the module case. 6) RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 370 and 700 Mv differential (185–350Mv single ended) when properly terminated. 7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP+ connector pin. Maximum supply current is 300mA. Recommended host board power supply filtering is shown below. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP+ input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP+ transceiver module will result in an inrush current of no more than 30Ma greater than the steady state value. VccR and VccT may be internally connected within the SFP+ transceiver module. 8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board.

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 10G CWDM(1470-1610nm) ZR SFP+ DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 10G CWDM(1470-1610nm) ER SFP+ DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Fri, 14 Nov 2025 06:02:23 +0000

SPECIFICATIONS
Product Model	SFP+10-CW1416-ER-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate	11.3Gbps	Channel Data Rate	10.138Gb/s
Power Budget	23dB
Wavelength	1470nm to 1610nm	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	CWDM EML	Receiver Type	IDP
TX Power	0~4dBm	Receiver Sensitivity	-23dBm
Digital Diagnostic Monitoring(DDM)	YES	Receiver Overload	-8dBm
Power Consumption	<1.5W	Protocols	SFF-8431 SFF-8432 SFF-8472
Operating Temperature(Commercial)	0 to 70℃ (32 to 158℉)	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Extended)	-20 to 75℃ (-4 to167℉)	Storage Temperature(Industrial)	-40 to 85℃ (-40 to 185℉)

PRODUCT PRESENTATION

The PHILISUN SFP+ 10G CWDM(1470-1610nm) ER LC DX series optical transceiver is designed for high-performance fiber communication applications up to 10G, fully compliant with the SFP+ MSA SFF-8431 specification. Optimized for single-mode fiber, this module operates across CWDM wavelengths, offering eight center wavelengths from 1470nm to 1610nm, with 20nm spacing between each wavelength. It provides a guaranteed optical link budget of 14dB. Featuring an SFP+ connector, the module supports hot-plug capability and requires only a single 3.3V power supply. The optical output can be disabled via an LVTTL logic high-level input (TX_DIS), and a Loss of Signal (RX_LOS) output is provided to indicate the loss of the input optical signal at the receiver. Additionally, this module offers digital diagnostic functions via a 2-wire serial interface, as defined by the SFF-8472 specification.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

CWDM* Wavelength
Band	Nomenclature	Wavelength(nm)
		Min.	Typ.	Max.
S-band short wavelength	K	1464	1470	1477.5
	L	1484	1490	1497.5
	M	1504	1510	1517.5
	N	1524	1530	1537.5
C-band conventional	O	1544	1550	1557.5
L-band long wavelength	P	1564	1570	1577.5
	Q	1584	1590	1597.5
	R	1604	1610	1617.5
CWDM*: 8 Wavelengths from 1470nm to 1610nm, each step 20nm.

Absolute Maximum Ratings
Parameter	Symbol	Min.	Typical	Max.	Unit
Maximum supply voltage 1	Vcc	-0.5	–	4.0	V
Storage temperature	Ts	-40	–	85	°C

Recommended Operating Conditions
Parameter	Symbol		Min.	Typical	Max.	Units
Case operating temperature	TC	Standard	0	–	+70	°C
		Extended	-20	–	75	°C
Supply voltage	Vcc		3.13	3.3	3.45	V
Supply current	Icc (0°C to 70°C)		–	350	455	mA
	Icc (-20°C to 75°C)		–	350	600.0	mA
Data rate	SFP+10-CW1416-ER-LCD		0.6	–	11.3	Gbps

Electrical Characteristics
Parameter	Symbol	Min.	Typ.	Max	Unit	Notes
Transmitter
CML inputs(Differential)	Vin	180	–	1000	mVpp	1
Input impedance (Differential)	Zin	85	100	115	ohms	–
Tx_DISABLE input voltage – high	–	2	–	Vcc+0.3	V	–
Tx_DISABLE input voltage – low	–	0	–	0.8	V	–
Tx_FAULT output voltage – high	–	2	–	Vcc+0.3	V	–
Tx_FAULT output voltage – low	–	0	–	0.8	V	–
Receiver
CML Outputs (Differential)	Vout	350	–	700	mVpp	1
Output impedance (Differential)	Zout	85	100	115	ohms	–
Rx_LOS output voltage – high	–	2	–	Vcc+0.3	V	–
Rx_LOS output voltage – low	–	0	–	0.8	V	–
MOD_DEF ( 0:2 )	VoH	2.5	–	–	V	2
MOD_DEF ( 0:2 )	VoL	0	–	0.5	V	2
Notes: 1. After internal AC coupling. 2. Reference the SFF-8472 MSA.

Optical Characteristics
Parameter	Symbol	Min.	Typical	Max.	Unit	Notes
Transmitter
Optical wavelength	λ	λc–6	–	λc+7.5	nm	2
-20dB spectrum width	Δλ	–	–	1	nm	–
Side mode suppression ratio	SMSR	30	λc	–	dB	–
Output opt. pwr(SFP+10-CW1416-ER-LCD)	Pout	-2	–	+4	dBm	1
Extinction ratio	ER	3.5	–	–	dB	–
Average launch power of OFF transmitter	POFF	–	–	-30	dBm	–
Transmitter dispersion penalty	TDP	–	–	3	dB	–
TX jitter	TXj	Per 802.3ae requirements			–	–
Relative intensity noise	RIN	–	–	-128	dB/Hz	–
Receiver
Receiver sensitivity	Pmin	–	–	-16	dBm	3
Maximum input power	Pmax	-1	–	–	dBm	–
Optical center wavelength	λ	1260	–	1620	nm	–
Receiver reflectance	Rrf	–	–	-12	dB	–
LOS de-assert	LOSD	–	–	-20	dBm	–
LOS assert	LOSA	-28	–	–	dBm	–
LOS hysteresis	–	1	–	–	dB	–
*Notes: 1. Output power is coupled into a 9/125μm SMF. 2. ITU-T G.694.2 CWDM wavelength from 1470nm to 1610nm, each step 20nm. 3. Average received power; BER less than 1E-12 and PRBS 231-1 test pattern.

SFP+ TRANSCEIVER ELECTRICAL PAD LAYOUT

PIN FUNCTION DEFINITIONS

Pin	Name	Function	Plug Seq.	Notes
1	VeeT	Transmitter ground	1	Note 5
2	TX Fault	Transmitter fault indication	3	Note 1
3	TX Disable	Transmitter disable	3	Note 2, module disables on high or open
4	SDA	Module definition 2	3	2-Wire serial interface data line.
5	SCL	Module definition 1	3	2-Wire serial Interface clock.
6	MOD-ABS	Module definition 0	3	Note 3
7	RS0	RX rate select(LVTTL).	3	No function implement
8	LOS	Loss of signal	3	Note 4
9	RS1	TX rate select(LVTTL).	1	No function implement
10	VeeR	Receiver ground	1	Note 5
11	VeeR	Receiver ground	1	Note 5
12	RD-	Inv. received data out	3	Note 6
13	RD+	Received data out	3	Note 6
14	VeeR	Receiver ground	1	Note 5
15	VccR	Receiver power	2	3.3V ± 5%, Note 7
16	VccT	Transmitter power	2	3.3V ± 5%, Note 7
17	VeeT	Transmitter ground	1	Note 5
18	TD+	Transmit data in	3	Note 8
19	TD-	Inv. transmit data in	3	Note 8
20	VeeT	Transmitter ground	1	Note 5
Notes: 1) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT/R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.2) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7K~10 K Ω resistor. Its states are: Low (0 – 0.8V): Transmitter on (>0.8, < 2.0V): Undefined High (2.0 – 3.465V): Transmitter Disabled Open: Transmitter Disabled3) Module Absent, connected to VeeT or VeeR in the module.4) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K –10KΩ resistor on host board. Pull up voltage between 2.0V and VccT/R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.5) The module signal ground contacts, VeeR and VeeT, should be isolated from the module case.6) RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 370 and 700 Mv differential (185–350Mv single ended) when properly terminated.7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP+ connector pin. Maximum supply current is 300mA. Recommended host board power supply filtering is shown below. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP+ input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP+ transceiver module will result in an inrush current of no more than 30Ma greater than the steady state value. VccR and VccT may be internally connected within the SFP+ transceiver module. 8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board.

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 10G CWDM(1470-1610nm) ER SFP+ DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 10G CWDM(1270-1450nm) ER SFP+ DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Fri, 14 Nov 2025 05:03:10 +0000

SPECIFICATIONS
Product Model	SFP+10-CW1214-ER-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate	11.3Gbps	Channel Data Rate	10.138Gb/s
Power Budget	23dB
Wavelength	1270nm to 1450nm	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	CWDM DFB	Receiver Type	IDP
TX Power	2~5dBm	Receiver Sensitivity	-21dBm
Digital Diagnostic Monitoring(DDM)	YES	Receiver Overload	-6dBm
Power Consumption	<1.5W	Protocols	SFF-8431 SFF-8472
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 10G CWDM (1270-1450nm) ER LC DX series optical transceiver is designed for high-performance fiber communication applications, such as 10G Ethernet (10GBASE-ZR/ZW), and is fully compliant with the SFP+ MSA SFF-8431 specification. This module is optimized for single-mode fiber and operates across CWDM wavelengths, with ten available center wavelengths ranging from 1270nm to 1450nm, spaced 20nm apart. It offers a guaranteed optical link budget of 23dB. The module features an SFP+ connector for hot-plug capability and requires only a single 3.3V power supply. The optical output can be disabled via an LVTTL logic high-level input (TX_DIS), and a Loss of Signal (RX_LOS) output is provided to indicate the absence of an optical signal at the receiver.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

CWDM* Wavelength
Band	Nomenclature	Wavelength(nm)
		Min.	Typ.	Max.
O-band original	A	1264	1270	1277.5
	B	1284	1290	1297.5
	C	1304	1310	1317.5
	D	1324	1330	1337.5
	E	1344	1350	1357.5
E-band extended	F	1364	1370	1377.5
	G	1384	1390	1397.5
	H	1404	1410	1417.5
	I	1424	1430	1437.5
	J	1444	1450	1457.5
S-band short wavelength	K	1464	1470	1477.5
	L	1484	1490	1497.5
	M	1504	1510	1517.5
	N	1524	1530	1537.5
C-band conventional	O	1544	1550	1557.5
L-band long wavelength	P	1564	1570	1577.5
	Q	1584	1590	1597.5
	R	1604	1610	1617.5
CWDM*: 18 Wavelengths from 1270nm to 1610nm, each step 20nm. Please contact PHILISUN to confirm whether the wavelength is available.

Absolute Maximum Ratings
Parameter	Symbol	Min.	Typical	Max.	Unit
Maximum supply voltage 1	Vcc	-0.5	–	4.0	V
Storage temperature	Ts	-40	–	85	°C

Recommended Operating Conditions
Parameter	Symbol	Min.	Typical	Max.	Unit
Case operating temperature	TC	-5	–	+70	°C
Supply voltage	Vcc	3.15	3.3	3.45	V
Supply current	Icc	–	–	430	mA
Data rate	–	0.614	–	11.3	Gbps

Electrical Characteristics
Parameter	Symbol	Min.	Typ.	Max	Unit	Notes
Transmitter
CML inputs(Differential)	Vin	180	–	1000	mVpp	1
Input impedance (Differential)	Zin	85	100	115	ohms	–
Tx_DISABLE input voltage – high	–	2	–	Vcc+0.3	V	–
Tx_DISABLE input voltage – low	–	0	–	0.8	V	–
Tx_FAULT output voltage – high	–	2	–	Vcc+0.3	V	–
Tx_FAULT output voltage – low	–	0	–	0.8	V	–
Receiver
CML Outputs (Differential)	Vout	350	–	700	mVpp	1
Output impedance (Differential)	Zout	85	100	115	ohms	–
Rx_LOS output voltage – high	–	2	–	Vcc+0.3	V	–
Rx_LOS output voltage – low	–	0	–	0.8	V	–
MOD_DEF ( 0:2 )	VoH	2.5	–	–	V	2
MOD_DEF ( 0:2 )	VoL	0	–	0.5	V	2
Notes: 1. After internal AC coupling. 2. Reference the SFF-8472 MSA.

Optical Characteristics
Parameter	Symbol	Min.	Typical	Max.	Unit	Notes
Transmitter
Output opt. pwr: 9/125 SMF	Pout	2	–	+5	dBm	1
Optical extinction ratio	ER	3.5	–	–	dB	–
Optical wavelength	λc	λc–6	λc	λc+7.5	nm	2
-20dB spectrum width	Δλ	–	–	1	nm	–
Side mode suppression ratio	SMSR	30	–	–	dB	–
Average launch power of OFF transmitter	POFF	–	–	-30	dBm	–
TX jitter	TXj	Per 802.3ae requirements			–	–
Relative intensity noise	RIN	–	–	-128	dB/Hz	–
Receiver
Receiver sensitivity @ 10.3125Gb/s	Pmin	–	–	21	dBm	3
Maximum input power	Pmax	-6	–	–	dBm	–
Optical center wavelength	λ	1260	–	1460	nm	–
Receiver reflectance	Rrf	–	–	-12	dB	–
LOS de-assert	LOSD	–	–	-23	dBm	–
LOS assert	LOSA	-35	–	–	dBm	–
LOS hysteresis	–	1	–	–	dB	–
*Notes: 1. Output power is coupled into a 9/125μm SMF. 2. ITU-T G.694.2 CWDM wavelength from 1270nm to 1450nm, each step 20nm. 3. Average received power; BER less than 1E-12 and PRBS 231-1 test pattern.

SFP+ TRANSCEIVER ELECTRICAL PAD LAYOUT

PIN FUNCTION DEFINITIONS

Pin	Name	Function	Plug Seq.	Notes
1	VeeT	Transmitter ground	1	Note 5
2	TX Fault	Transmitter fault indication	3	Note 1
3	TX Disable	Transmitter disable	3	Note 2, module disables on high or open
4	SDA	Module definition 2	3	2-Wire serial interface data line.
5	SCL	Module definition 1	3	2-Wire serial Interface clock.
6	MOD-ABS	Module definition 0	3	Note 3
7	RS0	RX rate select(LVTTL).	3	No function implement
8	LOS	Loss of signal	3	Note 4
9	RS1	TX rate select(LVTTL).	1	No function implement
10	VeeR	Receiver ground	1	Note 5
11	VeeR	Receiver ground	1	Note 5
12	RD-	Inv. received data out	3	Note 6
13	RD+	Received data out	3	Note 6
14	VeeR	Receiver ground	1	Note 5
15	VccR	Receiver power	2	3.3V ± 5%, Note 7
16	VccT	Transmitter power	2	3.3V ± 5%, Note 7
17	VeeT	Transmitter ground	1	Note 5
18	TD+	Transmit data in	3	Note 8
19	TD-	Inv. transmit data in	3	Note 8
20	VeeT	Transmitter ground	1	Note 5
Notes: 1) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT/R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.2) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7K~10 K Ω resistor. Its states are: Low (0 – 0.8V): Transmitter on (>0.8, < 2.0V): Undefined High (2.0 – 3.465V): Transmitter Disabled Open: Transmitter Disabled3) Module Absent, connected to VeeT or VeeR in the module.4) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K –10KΩ resistor on host board. Pull up voltage between 2.0V and VccT/R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. 5) The module signal ground contacts, VeeR and VeeT, should be isolated from the module case. 6) RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 370 and 700 Mv differential (185–350Mv single ended) when properly terminated. 7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP+ connector pin. Maximum supply current is 300mA. Recommended host board power supply filtering is shown below. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP+ input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP+ transceiver module will result in an inrush current of no more than 30Ma greater than the steady state value. VccR and VccT may be internally connected within the SFP+ transceiver module. 8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board.

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 10G CWDM(1270-1450nm) ER SFP+ DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。