SFP+ DWDM 10G Series – www.philisun.com

Generic Compatible 10G DWDM 50GHz ZR SFP+ 80km DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Fri, 14 Nov 2025 09:26:07 +0000

SPECIFICATIONS
Product Model	SFP+10-50DW-80(ZR)-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate	11.3Gbps	Channel Data Rate	10.3125Gbps
Effective Transmission Distance	80km
Wavelength	1529.16~1567.13nm（（Tunable）;1563.86nm-1528.77nm	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	Monolithic MZM Tunable TOSA	Receiver Type	APD
TX Power	-1~3dBm,-1~4dBm;0~5dBm	Receiver Sensitivity	-23dBm
Digital Diagnostic Monitoring(DDM)	YES	Receiver Overload	-7dBm
Power Consumption	C<2.0W,I<2.5W;C<1.65W	Protocols	SFF-8431 SFF-8472 SFF-8690 ITU-T G.698.1
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Industrial)	-40℃~+85℃	Storage Temperature(Industrial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 10G 50GHz DWDM 80km ZR LC DX transceiver is a high-performance cost-effective solution supporting multi-rate data transmission from 9.95Gbps to 11.3Gbps with CDR and 8.5Gbps bypassing CDR, delivering 80km transmission over single-mode fiber (SMF); featuring dual-section design with transmitter integrating laser driver/TTOSA and receiver combining APD photodiode with transimpedance amplifier (TIA); hot-pluggable into 20-pin connector with high-speed electrical interface based on low-voltage logic, 100-ohm differential impedance and AC coupling; TX_DIS disables optical output via LVTTL high-level input, Tx_Fault signals laser/safety issues, and RX_LOS indicates incoming optical signal loss; equipped with serial EEPROM supporting monitoring/configuration via 2-wire SFP management interface, with memory organized into lower area storing basic digital diagnostic (DD) data and upper area housing specific data in high-memory tables.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

Absolute Maximum Ratings
Parameter	Symbol	Min.	Max.	Unit	Notes
Storage temperature	Ts	-40	85	℃	–
Supply voltage	Vcc3	0	3.63	V	–
Relative humidity	RH	5	+85	%	Note1
Notes: [1] Non-condensing state.

Recommended Operating Conditions
Parameter	Symbol	Min.	Typ.	Max.	Unit	Notes
Operating case temperature	Tc	-5	25	85	°C	–
Supply voltage	Vcc	3.13	3.3	3.47	V	–
Power consumption	P	–	–	2.5	W	–
Data rate	–	8.5	10.3125	11.3	Gbps	–
Transmission distance	–	–	–	80	km	–

Transmitter Operating Characteristic-Optical, Electrical
Parameter	Symbol	Min.	Typical	Max	Unit	Note
Data rate	DR	8.5	10.3125	11.3	Gbps	–
Center wavelength	CW	191.30	–	196.05	THz	–
Wavelength range	λC	1529.16	–	1567.13	nm	–
Center frequqncy variation	CFV	–	–	+/-2.5	GHz	–
-20dB spectral width	Δλ20	–	–	0.3	nm	–
Side mode suppression ratio	SMSR	30	–	–	nm	–
Laser off power	Poff	–	–	-30	dBm	–
Optical eye mask	EMM	5	–	–	%	–
Average optical power	PO	-1	–	3	dBm	–
Extinction ratio	ER	8.2	–		dB	–
Cross point of eye	CP	40	–	52	%	–
Transmitter dispersion renalty	TDP	–	–	2	dB	–
Relative intensity noise	RIN 12OMA	–	–	-128	dB/Hz	–
Optical eye mask	ORLT	–	–	-27	dB	–
Tx Input diff voltage	VI	200	–	700	mV	–

Receiver Operating Characteristic-Optical, Electrical
Parameter	Symbol	Min.	Typical	Max.	Unit	Note
Data rate	DR	8.5	10.3125	11.3	Gbps	–
Center wavelength	CW	1260	–	1600	nm	–
Sensitivity @(BER=1E-12, PRBS 2^31-1, NRZ, 9.95Gbps~10.7Gbps data rate	Psen	–	–	-23	dBm	–
Sensitivity @(BER=1.0E-04, PRBS 2^31- 1, NRZ,11.3Gbps data rate)	Psen	–	–	-26	dBm	–
B2B OSNR Tolerance @ 1E-4	–	–	–	16	dB	–
Input optical power(no damaged)	IOP	4	–	–	dBm	–
Saturation power（EOL）	SP	-7	–	–	dBm	–
Loss of signal – asserted	LosA	-35	–	–	dBm	–
Loss of signal- deasserted	LosD	–	–	-28	dBm	–
Hysteresis	LosH	0.5	–	–	dB	–
Rx output diff voltage	Vo	250	–	850	mV	–
Loss of signal voltage	VOH	Vcc-0.5	–	Vcc+0.3	V	–
Loss of signal voltage	VOL	0	–	0.4	V	–

Digital Diagnostic Functions
Parameter	Symbol	Min.	Typical	Max	Units	Notes
Temperature monitor absolute error	DMI_Temp	-3	–	3	℃	Over operating temperature
Supplyvoltage monito rabsolute error	DMI_Vcc	-3%	–	3%	V	–
Bias current monitor absolute error	DMI_Ibias	-10%	–	10%	mA	–
Lase rpower monitor absolute error	DMI_Tx	-3	–	3	dB	–
RX power monitor absolute error	DMI_Rx	-3	–	3	dB	–

Control and StatusI/OTiming Characteristics
Parameter	Symbol	Min.	Typical	Max	Units	Notes
TX disable assert time	t_off	–	–	100	µs	Note1
TX disable negate time	t_on	–	–	2	ms	Note2
Time to initialize including reset of TX_fault	t_init	–	–	300	ms	Note3
Time to initialize cooled module and time to power up a cooled module to power level II	t_start_up_co oled	–	–	90	s	Note4
TX fault assert time	t_fault_on	–	–	1	ms	Note5
TX fault reset time	t_reset	10	–	–	µs	Note6
LOS assert time	t_loss_on	–	–	100	µs	Note7
LOS deassert time	t_loss_off	–	–	100	µs	Note8
Notes: [1] Time from rising edge of TX Disable to when the optical output falls below 10% of nominal. [2] Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal. [3] From power on or negation of TX Fault using TX Disable. [4] From power supply or hot plug or TX Disable negated during power up, or TX Fault recovery, until cooled power level I part (or cooled power level II part during Fault recovery) the SFP+ is fully operational [5] Time from fault to TX fault on. [6] Time from TX fault to TX nominal. [7] Time from LOS state to RX LOS assert. [8] Time from non-LOS state to RX LOS deassert.

PIN-OUT DEFINITIONS

	Logic	Symbol	Name/Description	Note
1	–	VeeT	Module transmitter ground	Note1
2	LVTTL-O	TX_fault	Module transmitter fault	Note2
3	LVTTL-I	TX_disable	Transmitter disable;Turnsofftrans mitterlaseroutput	Note3
4	LVTTL-I/O	SDA	2-Wire serial interface data line(Same as MOD-DEF2 asdefinedin the INF-8074i)	Note4
5	LVTTL-I/O	SCL	2-Wire serial interface clock(Same as MOD-DEF1 as defined intheINF-8074i)	Note4
6	–	MOD-ABS	Module absent, connected to VeeT or VeeR in the module	Note5
7	LVTTL-I	RS0	Rate select 0	–
8	LVTTL-O	RX_LOS	Receiver Loss of Signal indication (In FC designated as RX_LOS, in SONET designated as LOS, and in ethernet designated at signal detect)	Note2
9	LVTTL-I	RS1	Rate select 1	–
10	–	VeeR	Module receiver ground	Note1
11	–	VeeR	Module receiver ground	Note1
12	CML-O	RD-	Receiver inverted data output	–
13	CML-O	RD+	Receiver non inverted data output	–
14	–	VccR	Module receiver ground	Note1
15	–	VeeR	Module receiver 3.3 V supply	–
16	–	VccT	Module transmitter 3.3 V supply	Note1
17	–	VeeT	Module transmitter ground	–
18	CML- I	TD+	Transmitter non-inverted data input	–
19	CML- I	TD-	Transmitter inverted data input	–
20	–	VeeT	Module yransmitter ground	Note1
Notes: [1]The module signal ground pins, VeeR and VeeT, shall be isolated from the module case.[2]This pin is an open collector/drain output pin and shall be pulled up with 4.7k-10kohms to Host_Vcc on the host board. Pull ups can be connected to multiple power supplies, however the host board design shall ensure that no module pin has voltage exceeding module VccT/R + 0.5 V.[3]This pin is an open collector/drain input pin and shall be pulled up with 4.7k-10kohms to VccT in the module. [4]See SFF-8431 4.2 2-wire Electrical Specifications. [5]This pin shall be pulled up with 4.7k-10kohms to Host_Vcc on the host board

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 10G DWDM 50GHz ZR SFP+ 80km DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 10G DWDM 50GHz ER SFP+ 40km DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Fri, 14 Nov 2025 08:23:18 +0000

SPECIFICATIONS
Product Model	SFP+10-50DW-40(ER)-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate	11.3Gbps	Channel Data Rate	10.3125Gbps
Effective Transmission Distance	40km
Wavelength	1529.16~1567.13nm（Tunable）	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	Monolithic MZM Tunable TOSA	Receiver Type	PIN
TX Power	-1~3dBm,-1~4dBm	Receiver Sensitivity	-16dBm
Digital Diagnostic Monitoring(DDM)	YES	Receiver Overload	-1dBm
Power Consumption	C<2.1W,I<2.5W	Protocols	SFF-8431 SFF-8472 SFF-8690 IEEE 802.3ae CL 52
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Industrial)	-40℃~+85℃	Storage Temperature(Industrial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 10G 50GHz DWDM 40km ER LC DX is a high performance, cost effective module supporting multi rate 9.95Gbps to 11.3Gbps with CDR, 8.5Gbps bypass CDR, and transmission distance up to 40km on SM fiber; the transceiver consists of two sections: transmitter incorporating a laser driver and TTOSA, and receiver with PIN integrated transimpedance preamplifier (TIA); this hot-pluggable module connects via 20-pin connector, featuring high-speed electrical interface based on low voltage logic with nominal 100ohms differential impedance and AC coupling; optical output is disabled by LVTTL high-level TX_DIS input, while Tx_Fault indicates laser-related faults and RX_LOS signals receiver input loss; its serial EEPROM enables monitoring/configuration access via 2-wire SFP management interface using single address A0h, with memory map divided into lower area (storing basic DD data) and upper area housing specific data in high memory tables.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

Absolute Maximum Ratings
Parameter	Symbol	Min.	Max.	Unit	Notes
Storage temperature	Ts	-40	85.0	℃	–
Power supply voltage	Vcc3	0	3.63	V	–
Relative humidity(noncondensation)	RH	5	+85	%	Note1
Damage threshold	Pmax	–	–	dBm	–

Recommended Operating Conditions
Parameter	Symbol	Min.	Typ.	Max.	Unit	Notes
Operating case temperature	Tc	0	25	75	°C	–
Supply voltage	Vcc	3.13	3.3	3.47	V	–
Power supply current	Pd	–	–	670	mA	–
Data rate	–	8.5	10.3125	11.3	Gbps	–
Transmission distance	–	–	–	40	km	–

Transmitter Operating Characteristic-Optical, Electrical
Parameter	Symbol	Min.	Typical	Max	Unit	Note
Data rate	DR	8.5	10.3125	11.3	Gbps	–
Center wavelength	CW	191.3	–	196.05	THz	–
Wavelength range	λC	1529.16	–	1567.13	nm	–
Center frequqncy variation	CFV	0	–	+/-2.5	GHz	–
-20dB spectral width	Δλ20	–	–	0.3	nm	–
Side mode suppression ratio	SMSR	30	–	–	nm	–
Laser off power	Poff	–	–	-30	dBm	–
Transmitter reflectance	TR	–	–	-12	dB	–
Average optical power	PO	-1	0.5	3	dBm	–
Extinction ratio	ER	8.2	–		dB	–
Cross point of eye	CP	0.4	–	0.52		–
Transmitter dispersion renalty	TDP		–	3	dB	–
Transmitter dispersion tolerance(CD window with 2dB OSNR penalty)	TDT	-700	–	700	km ps/nm	–
Relative intensity noise	RIN12OMA	–	–	-128	dB/Hz	–
Optical eye mask	EMM	5	–	–	–	–
Tx Input diff voltage	VI	200	–	850	mV	–

Receiver Operating Characteristic-Optical, Electrical
Parameter	Symbol	Min.	Typical	Max.	Unit	Note
Data rate	DR	8.5	10.3125	11.3	Gbps	–
Center wavelength	CW	1260	–	1600	nm	–
Sensitivity @(BER=1E-12, PRBS 2^31-1, NRZ, 9.95Gbps~10.7Gbps data rate	Psen	1529.16	–	-16(EOL)	dBm	–
Sensitivity @(BER=2.0E-03, PRBS 2^31-1,NRZ,11.3Gbps data rate, dispersion 800ps/nm, at room temperature and OSNR >31dB)	Psen	–	–	-19 (EOL)	dBm	–
B2B OSNR Tolerance BOL @ 2E-3 Test condition： A:optical filter type and bandwidth：flattop filter -3dB bandwidth 84 GHz, OSA res 0.1nm for noise bandwidth. B: Input optical power range： 0~-14dBm C:9.9Gbps~11.3Gbps data rate range D:-5~70℃ E：Under the optimal threshold or 50% threshold	–	–	–	13.5	dB	–
B2B OSNR Tolerance BOL @ 2E-3 Test condition： A:optical filter type and bandwidth：flattop filter -3dB bandwidth 84 GHz, OSA res 0.1nm for noise bandwidth. B: Input optical power range： 0~-14dBm C:9.9Gbps~11.3Gbps data rate range D:-5~70℃ E：Under the optimal threshold or 50% threshold	–	–	–	14.0	dB	–
Saturation power（EOL）	SP	-1	–	–	dBm	–
Input optical power(no	IOP	4	–	–	dBm	–

Receiver Operating Characteristic-Optical, Electrical
Parameter	Symbol	Min.	Typical	Max.	Unit	Note
Data rate	DR	8.5	10.3125	11.3	Gbps	–
Center wavelength	CW	1260	–	1600	nm	–
Sensitivity @(BER=1E-12, PRBS 2^31-1, NRZ, 9.95Gbps~10.7Gbps data rate	Psen	1529.16	–	-16(EOL)	dBm	–
Sensitivity @(BER=2.0E-03, PRBS 2^31-1,NRZ,11.3Gbps data rate, dispersion 800ps/nm, at room temperature and OSNR >31dB)	Psen	–	–	-19 (EOL)	dBm	–
B2B OSNR Tolerance BOL @ 2E-3 Test condition： A:optical filter type and bandwidth：flattop filter -3dB bandwidth 84 GHz, OSA res 0.1nm for noise bandwidth. B: Input optical power range： 0~-14dBm C:9.9Gbps~11.3Gbps data rate range D:-5~70℃ E：Under the optimal threshold or 50% threshold	–	–	–	13.5	dB	–
B2B OSNR Tolerance BOL @ 2E-3 Test condition： A:optical filter type and bandwidth：flattop filter -3dB bandwidth 84 GHz, OSA res 0.1nm for noise bandwidth. B: Input optical power range： 0~-14dBm C:9.9Gbps~11.3Gbps data rate range D:-5~70℃ E：Under the optimal threshold or 50% threshold	–	–	–	14.0	dB	–
Saturation power（EOL）	SP	-1	–	–	dBm	–
Input optical power(no	IOP	4	–	–	dBm	–

Digital Diagnostic Functions
Parameter	Symbol	Min.	Typical	Max	Units	Notes
Temperature monitor absolute error	DMI_Temp	-3	–	3	℃	Over operating temperature
Supplyvoltage monito rabsolute error	DMI_Vcc	-3%	–	3%	V	Over operating voltage
Bias current monitor absolute error	DMI_Ibias	-10%	–	10%	mA	–
Lase rpower monitor absolute error	DMI_Tx	-3	–	3	dB	–

Control and StatusI/OTiming Characteristics
Parameter	Symbol	Min.	Typical	Max	Units	Notes
TX disable assert time	t_off	–	–	100	µs	Note1
TX disable negate time	t_on	–	–	2	ms	Note2
Time to initialize including reset of TX_fault	t_init	–	–	300	ms	Note3
TX fault assert time	t_fault_on	–	–	1	ms	Note4
TX fault reset time	t_reset	10	–	–	µs	Note5
LOS assert time	t_loss_on	–	–	100	µs	Note6
LOS deassert time	t_loss_off	–	–	100	µs	Note7
Notes: [1]Time from rising edge of TX Disable to when the optical output falls below 10% of nominal. [2]Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal. [3]From power on or negation of TX Fault using TX Disable. [4]Time from fault to TX fault on. [5]Time from TX fault to TX nominal. [6]Time from LOS state to RX LOS assert. [7]Time from non-LOS state to RX LOS deassert.

PIN-OUT DEFINITIONS

	Logic	Symbol	Name/Description	Note
1	–	VeeT	Module transmitter ground	Note1
2	LVTTL-O	TX_fault	Module transmitter fault	Note2
3	LVTTL-I	TX_disable	Transmitter disable;Turnsofftrans mitterlaseroutput	Note3
4	LVTTL-I/O	SDA	2-Wire serial interface data line(Same as MOD-DEF2 asdefinedin the INF-8074i)	Note4
5	LVTTL-I/O	SCL	2-Wire serial interface clock(Same as MOD-DEF1 as defined intheINF-8074i)	Note4
6	–	MOD-ABS	Module absent, connected to VeeT or VeeR in the module	Note5
7	LVTTL-I	RS0	Rate select 0	–
8	LVTTL-O	RX_LOS	Receiver Loss of Signal indication (In FC designated as RX_LOS, in SONET designated as LOS, and in ethernet designated at signal detect)	Note2
9	LVTTL-I	RS1	Rate select 1	–
10	–	VeeR	Module receiver ground	Note1
11	–	VeeR	Module receiver ground	Note1
12	CML-O	RD-	Receiver inverted data output	–
13	CML-O	RD+	Receiver non inverted data output	–
14	–	VccR	Module receiver ground	Note1
15	–	VeeR	Module receiver 3.3 V supply	–
16	–	VccT	Module transmitter 3.3 V supply	Note1
17	–	VeeT	Module transmitter ground	–
18	CML- I	TD+	Transmitter non-inverted data input	–
19	CML- I	TD-	Transmitter inverted data input	–
20	–	VeeT	Module yransmitter ground	Note1
Notes: [1]The module signal ground pins, VeeR and VeeT, shall be isolated from the module case.[2]This pin is an open collector/drain output pin and shall be pulled up with 4.7k-10kohms to Host_Vcc on the host board. Pull ups can be connected to multiple power supplies, however the host board design shall ensure that no module pin has voltage exceeding module VccT/R + 0.5 V.[3]This pin is an open collector/drain input pin and shall be pulled up with 4.7k-10kohms to VccT in the module.[4]See SFF-8431 4.2 2-wire Electrical Specifications. [5]This pin shall be pulled up with 4.7k-10kohms to Host_Vcc on the host board

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 10G DWDM 50GHz ER SFP+ 40km DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 10G DWDM 100GHz ZR SFP+ 80km DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Fri, 14 Nov 2025 07:47:55 +0000

SPECIFICATIONS
Product Model	SFP+10-100DW-80(ZR)-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate	11.3Gbps	Channel Data Rate	10.5Gbps
Effective Transmission Distance	80km
Wavelength	1528.77nm to 1563.86nm	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	DWDM EML	Receiver Type	IDP
TX Power	0~4dBm	Receiver Sensitivity	-23dBm
Digital Diagnostic Monitoring(DDM)	YES	Receiver Overload	-7dBm
Power Consumption	C<1.5W,I<1.8W	Protocols	SFF-8431 MSA SFF-8432 MSA
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Industrial)	-40℃~+85℃	Storage Temperature(Industrial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 10G 100GHz DWDM 80km ZR LC DX series single-mode transceiver is a compact, pluggable module designed for duplex optical data communications. Tailored for DWDM networking equipment in metropolitan access and core networks, this module operates across nominal DWDM wavelengths from 1528nm to 1566nm, as specified by ITU-T standards. It is fully compliant with the SFF-8431 and SFF-8432 MSA specifications.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

General Specifications
Parameter	Symbol	Min	Typ.	Max	Unit	Ref.
Module form factor	BR	9.95	–	10.5	Gb/s	1
Number of lanes	BER	–	–	10-12	–	2
Maximum aggregate data rate	Lmax	–	80	–	km	–
*Notes: 1. 10GBASE-ZR, 10GBASE-ZW, 1200-SM-LL-L 10GFC. 2. Tested with a PRBS 231-1 test pattern

Absolute Maximum Ratings
Parameter	Symbol	Min.	Typ.	Max.	Unit
Storage temperature	Ts	-40	–	85	°C
Supply voltage	Vcc	-0.5	–	4	V
Operating relative humidity	–	–	–	85	%

Electrical Characteristics
Parameter		Symbol	Min.	Typ.	Max	Unit	Notes
Power supply voltage		Vcc	3.15	3.3	3.45	V	–
Power supply current		Icc (0℃ to 70℃)	–	350	455	mA	–
		Icc (-40℃ to 85℃)	–	350	545	mA	–
Date rate		DR	0.6	–	11.3	Gbps	Date rate
Transmitter
TX_dis	Disable	–	2	–	Vcc+0.3	V	–
	Enable	–	0	–	0.8		–
TX_FAULT	Fault	–	2	–	Vcc+0.3	V	–
	Normal	–	0	–	0.5		–
CML inputs (Differential)		Vin	250		1000	mVpp	AC coupled input
Input impedance (Differential)		Zin	85	100	115	ohm	Rin > 100 kohm @ DC
Receiver
CML Outputs (Differential)		Vout	350	–	700	mVpp	AC coupled outputs
RX_LOS	Loss	–	2	–	Vcc+0.3	V	–
	Normal	–	0	–	0.8		–
Output impedance (Differential)		Zout	85	100	115	ohm	–
MOD_DEF ( 0:2 )		VoH	2.5	–	–	V	With serial ID
		VoL	0	–	0.5	V

Optical Characteristics
Parameter	Symbol	Min.	Typ.	Max.	Unit
Data rate	–	0.6	–	11.3	Gbps
Transmitter
Side mode suppression ratio	SMSR	30	–	–	dB
Center wavelength spacing	–	–	100	–	GHz
	–		0.8	–	nm
Average output power	Pout	0	–	4	dBm
Average launch power (Tx: OFF)	POFF	–	–	-30	dBm
Extinction ratio	ER	6	–	–	dB
Transmitter dispersion penalty @1600ps/nm	TDP	–	–	3	dB
Pout@TX disable asserted	Pout	–	–	-45	dBm
Relative intensity noise	RIN	–	–	-128	dB/Hz
TX jitter	TXj	Per 802.3ae requirements
Receiver
Receiver sensitivity	Pmin	–	–	-23	dBm
Receiver overload	Pmax	-7	–	–	dBm
LOS de-assert	LOSD	–	–	-24	dBm
LOS assert	LOSA	-40	–	–	dBm
LOS hysteresis	–	0.5	–	–	dB
Notes: 1. Output is coupled into a 9/125μm single-mode fiber. 2. Minimum average optical power measured at the BER less than 1E-12. The measurepattern is PRBS 231-1. 3. CML logic, internally AC coupled.

Wavelength Table
Channel	Frequency (THz)	Center wavelength(nm)	Channel	Frequency (THz)	Center wavelength(nm)
17	191.7	1563.86	40	194	1545.32
18	191.8	1563.05	41	194.1	1544.53
19	191.9	1562.23	42	194.2	1543.73
20	192	1561.41	43	194.3	1542.94
21	192.1	1560.61	44	194.4	1542.14
22	192.2	1559.79	45	194.5	1541.35
23	192.3	1558.98	46	194.6	1540.56
24	192.4	1558.17	47	194.7	1539.77
25	192.5	1557.36	48	194.8	1538.98
26	192.6	1556.55	49	194.9	1538.19
27	192.7	1555.75	50	195	1537.4
28	192.8	1554.94	51	195.1	1536.61
29	192.9	1554.13	52	195.2	1535.82
30	193	1553.33	53	195.3	1535.04
31	193.1	1552.52	54	195.4	1534.25
32	193.2	1551.72	55	195.5	1533.47
33	193.3	1550.92	56	195.6	1532.68
34	193.4	1550.12	57	195.7	1531.9
35	193.5	1549.32	58	195.8	1531.12
36	193.6	1548.51	59	195.9	1530.33
37	193.7	1547.72	60	196	1529.55
38	193.8	1546.92	61	196.1	1528.77
39	193.9	1546.12	–	–	–

PIN DESCRIPTION

Pin	Name	Function	Plug Seq.	Notes
1	VeeT	Transmitter ground	1	Note 5
2	TX Fault	Transmitter fault indication	3	Note 1
3	TX Disable	Transmitter disable	3	Note 2, module disables on high or open
4	SDA	Module definition 2	3	Note 3, data line for serial ID.
5	SCL	Module definition 1	3	Note 3, clock line for serial ID.
6	MOD-ABS	Module definition 0	3	Note 3
7	RS0	RX rate select(LVTTL).	3	Rate select 0, optionally controls SFP+ module receiver. This pin is pulled low to VeeT with a>30K resistor.
8	LOS	Loss of signal	3	Note 4
9	RS1	TX rate select(LVTTL).	1	Rate select 1, optionally controls SFP+ module transmitter. This pin is pulled low to VeeT with a >30K resistor.
10	VeeR	Receiver ground	1	Note 5
11	VeeR	Receiver ground	1	Note 5
12	RD-	Inv. received data out	3	Note 6
13	RD+	Received data out	3	Note 7
14	VeeR	Receiver ground	1	Note 5
15	VccR	Receiver power	2	3.3V ± 5%, Note 7
16	VccT	Transmitter power	2	3.3V ± 5%, Note 7
17	VeeT	Transmitter ground	1	Note 5
18	TD+	Transmit data in	3	Note 8
19	TD-	Inv. transmit data in	3	Note 8
20	VeeT	Transmitter ground	1	Note 5
Notes: 1) . TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10K resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high,output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.2) . TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7-10 K resistor. Its states are: Low (0 – 0.8V): Transmitter on (>0.8, < 2.0V): Undefined High (2.0 – 3.465V):Transmitter Disabled Open: Transmitter Disabled3)Module absent, connected to VEET or VEER in the module.4) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K–10K resistor. Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.5) VeeR and VeeT may be internally connected within the SFP+ module. 6) RD-/+: These are the differential receiver outputs. They are AC coupled 100 differential lines which should be terminated with100(differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. 7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP+ connector pin. Maximum supply current is 300mA. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP+ input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP+ transceiver module will result in an inrush current of no more than 30mA greater than the steady state value. VccR and VccT may be internall connected within the SFP+ transceiver module. 8) . TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100 differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board.

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 10G DWDM 100GHz ZR SFP+ 80km DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。

Generic Compatible 10G DWDM 100GHz ER SFP+ 40km DOM Duplex LC SMF Optical Transceiver Module

philisun001 — Fri, 14 Nov 2025 07:12:23 +0000

SPECIFICATIONS
Product Model	SFP+10-100DW-40(ER)-LCD	Manufacturer Brand	PHILISUN
Package Type	SFP+	Optical Connector	Duplex LC
Max Data Rate	11.3Gbps	Channel Data Rate	10.5Gbps
Effective Transmission Distance	40km
Wavelength	1528.77nmto1563.86nm	Operating Voltage	3.3V
Fiber Type	SMF	Core Size	9/125µm
Transmitter Type	DWDM EML	Receiver Type	IDP
TX Power	-1~4dBm	Receiver Sensitivity	-16dBm
Digital Diagnostic Monitoring(DDM)	YES	Receiver Overload	0dBm
Power Consumption	C<1.5W,I<1.8W	Protocols	SFF-8431 MSA SFF-8432 MSA SFF 8472
Operating Temperature(Commercial)	0℃~+70℃	Storage Temperature(Commercial)	-40℃~+85℃
Operating Temperature(Industrial)	-40℃~+85℃	Storage Temperature(Industrial)	-40℃~+85℃

PRODUCT PRESENTATION

The PHILISUN SFP+ 10G 100GHz DWDM 40km ER LC DX series single-mode transceiver is a compact pluggable module designed for duplex optical data communications. Ideal for deployment in DWDM networking equipment within metropolitan access and core networks, this module operates at nominal DWDM wavelengths from 1528nm to 1566nm, in accordance with ITU-T specifications. It is fully compliant with SFF-8431 and SFF-8432 MSA standards.

TRANSCEIVER SERIES PRODUCTS

PRODUCTION & TESTING EQUIPMENT

PERFORMANCE PARAMETER

General Specifications
Parameter	Symbol	Min	Typ.	Max	Unit	Ref.
Module form factor	BR	9.95	–	10.5	Gb/s	1
Number of lanes	BER	–	–	10-12	–	2
Maximum aggregate data rate	Lmax	–	40	–	km	–
*Notes: 1. 10GBASE-ER, 10GBASE-EW, 1200-SM-LL-L 10GFC. 2. Tested with a PRBS 231-1 test pattern.

Absolute Maximum Ratings
Parameter	Symbol	Min.	Typ.	Max.	Unit
Storage temperature	Ts	-40	–	85	°C
Supply voltage	Vcc	-0.5	–	4	V
Operating relative humidity	–	–	–	85	%

Recommended Operating Conditions
Parameter	Symbol	Min.	Typical	Max.	Unit
Case operating temperature	TC	-5	–	+70	°C
Supply voltage	Vcc	3.15	3.3	3.45	V
Supply current	Icc	–	–	430	mA
Data rate	–	0.614	–	11.3	Gbps

Electrical Characteristics
Parameter		Symbol	Min.	Typ.	Max	Unit	Notes
Power supply voltage		Vcc	3.15	3.3	3.45	V	–
Power supply current		Icc (0℃ to 70℃)	–	350	455	mA	–
		Icc (-40℃ to 85℃)	–	350	545	mA	–
Date rate		DR	0.6	–	11.3	Gbps	Date rate
Transmitter
TX_dis	Disable	–	2	–	Vcc+0.3	V	–
	Enable	–	0	–	0.8		–
TX_FAULT	Fault	–	2	–	Vcc+0.3	V	–
	Normal	–	0	–	0.5		–
CML inputs (Differential)		Vin	250		1000	mVpp	AC coupled input
Input impedance (Differential)		Zin	85	100	115	ohm	Rin > 100 kohm @ DC
Receiver
CML Outputs (Differential)		Vout	350	–	700	mVpp	AC coupled outputs
RX_LOS	Loss	–	2	–	Vcc+0.3	V	–
	Normal	–	0	–	0.8		–
Output impedance (Differential)		Zout	85	100	115	ohm	–
MOD_DEF ( 0:2 )		VoH	2.5	–	–	V	With serial ID
		VoL	0	–	0.5	V

Optical Characteristics
Parameter	Symbol	Min.	Typ.	Max.	Unit
Data rate	–	0.6	–	11.3	Gbps
Transmitter
Side mode suppression ratio	SMSR	30	–	–	dB
Center wavelength spacing	–	–	100	–	GHz
	–		0.8	–	nm
Average output power	Pout	-1	–	4	dBm
Average launch power (Tx: OFF)	POFF	–	–	-30	dBm
Extinction ratio	ER	6	–	–	dB
Transmitter dispersion penalty @800ps/nm	TDP	–	–	3.0	dB
Pout@TX disable asserted	Pout	–	–	-45	dBm
Relative intensity noise	RIN	–	–	-128	dB/Hz
TX jitter	TXj	Per 802.3ae requirements
Receiver
Receiver sensitivity	Pmin	–	–	-16	dBm
Receiver overload	Pmax	0	–	–	dBm
LOS de-assert	LOSD	–	–	-17	dBm
LOS assert	LOSA	-30	–	–	dBm
LOS hysteresis	–	0.5	–	–	dB
*Notes: 1. Output is coupled into a 9/125μm single-mode fiber. 2. Minimum average optical power measured at the BER less than 1E-12. The measurepattern is PRBS 231-1. 3. CML logic, internally AC coupled.

Wavelength Table
Channel	Frequency (THz)	Center wavelength(nm)	Channel	Frequency (THz)	Center wavelength(nm)
17	191.7	1563.86	40	194	1545.32
18	191.8	1563.05	41	194.1	1544.53
19	191.9	1562.23	42	194.2	1543.73
20	192	1561.41	43	194.3	1542.94
21	192.1	1560.61	44	194.4	1542.14
22	192.2	1559.79	45	194.5	1541.35
23	192.3	1558.98	46	194.6	1540.56
24	192.4	1558.17	47	194.7	1539.77
25	192.5	1557.36	48	194.8	1538.98
26	192.6	1556.55	49	194.9	1538.19
27	192.7	1555.75	50	195	1537.4
28	192.8	1554.94	51	195.1	1536.61
29	192.9	1554.13	52	195.2	1535.82
30	193	1553.33	53	195.3	1535.04
31	193.1	1552.52	54	195.4	1534.25
32	193.2	1551.72	55	195.5	1533.47
33	193.3	1550.92	56	195.6	1532.68
34	193.4	1550.12	57	195.7	1531.9
35	193.5	1549.32	58	195.8	1531.12
36	193.6	1548.51	59	195.9	1530.33
37	193.7	1547.72	60	196	1529.55
38	193.8	1546.92	61	196.1	1528.77
39	193.9	1546.12	–	–	–

PIN DESCRIPTION

Pin	Name	Function	Plug Seq.	Notes
1	VeeT	Transmitter ground	1	Note 5
2	TX Fault	Transmitter fault indication	3	Note 1
3	TX Disable	Transmitter disable	3	Note 2, module disables on high or open
4	SDA	Module definition 2	3	Note 3, data line for serial ID.
5	SCL	Module definition 1	3	Note 3, clock line for serial ID.
6	MOD-ABS	Module definition 0	3	Note 3
7	RS0	RX rate select(LVTTL).	3	Rate select 0, optionally controls SFP+ module receiver. This pin is pulled low to VeeT with a>30K resistor.
8	LOS	Loss of signal	3	Note 4
9	RS1	TX rate select(LVTTL).	1	Rate select 1, optionally controls SFP+ module transmitter. This pin is pulled low to VeeT with a >30K resistor.
10	VeeR	Receiver ground	1	Note 5
11	VeeR	Receiver ground	1	Note 5
12	RD-	Inv. received data out	3	Note 6
13	RD+	Received data out	3	Note 7
14	VeeR	Receiver ground	1	Note 5
15	VccR	Receiver power	2	3.3V ± 5%, Note 7
16	VccT	Transmitter power	2	3.3V ± 5%, Note 7
17	VeeT	Transmitter ground	1	Note 5
18	TD+	Transmit data in	3	Note 8
19	TD-	Inv. transmit data in	3	Note 8
20	VeeT	Transmitter ground	1	Note 5
Notes: 1) . TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10K resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high,output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.2) . TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7-10 K resistor. Its states are: Low (0 – 0.8V): Transmitter on (>0.8, < 2.0V): Undefined High (2.0 – 3.465V):Transmitter Disabled Open: Transmitter Disabled3)Module absent, connected to VEET or VEER in the module.4) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K–10K resistor. Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. 5) VeeR and VeeT may be internally connected within the SFP+ module. 6) RD-/+: These are the differential receiver outputs. They are AC coupled 100 differential lines which should be terminated with100(differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. 7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP+ connector pin. Maximum supply current is 300mA. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP+ input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP+ transceiver module will result in an inrush current of no more than 30mA greater than the steady state value. VccR and VccT may be internall connected within the SFP+ transceiver module. 8) . TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100 differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board.

PRODUCT CERTIFICATION

QUALITY ADVANTAGE

COMPATIBLE BRANDS

CONFIGURATION INFORMATION

The form can be filled in the actual website url.

Generic Compatible 10G DWDM 100GHz ER SFP+ 40km DOM Duplex LC SMF Optical Transceiver Module最先出现在www.philisun.com。